CAME Z Series 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} CAME Z Series에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. CAME Z Series 12 페이지. Control board
CAME Z Series에 대해서도 마찬가지입니다: 매뉴얼 (8 페이지), 매뉴얼 (20 페이지), 매뉴얼 (4 페이지), 매뉴얼 (4 페이지), 매뉴얼 (17 페이지), 매뉴얼 (17 페이지), 매뉴얼 (13 페이지), 매뉴얼 (13 페이지), 매뉴얼 (16 페이지), 매뉴얼 (16 페이지), 매뉴얼 (12 페이지), 매뉴얼 (12 페이지), 매뉴얼 (18 페이지), 설치 매뉴얼 (11 페이지), 매뉴얼 (8 페이지), 매뉴얼 (20 페이지), 매뉴얼 (12 페이지), 매뉴얼 (12 페이지), 기술 문서 매뉴얼 (16 페이지), 사용 설명서 (16 페이지), 지침 (4 페이지), 빠른 매뉴얼 (2 페이지), 연결 매뉴얼 (4 페이지), 매뉴얼 (4 페이지), 매뉴얼 (12 페이지), 매뉴얼 (20 페이지), 매뉴얼 (15 페이지), 사용 설명서 (12 페이지), 매뉴얼 (16 페이지)

페이지 인쇄
CAME Z Series 빠른 시작 매뉴얼
Description
Electric panel suitable for controlling the
automation of 230V swing gates with up to
320W power.
Fully designed and built by CAME CAN-
CELLI AUTOMATICI S.p.A., it complies
with regulations in force.
ABS container with IP54 protection level.
The panel runs on 230V with a 50÷60 Hz
frequency on terminals L-N, and the inlet is
protected with 5A fuses.
Control circuit and accessory power sup-
ply: 24V, protected by a 1.6A fuse.
The accessories' overall wattage must not
be over 20W.
Safety
Reopening during closure: safety device
connected with terminals 2-C1. The photo-
electric cells detect an obstacle while the
gate is closing, causing the gate to reverse
the direction of movement until it is fully
open.
Total stop: safety device connected
to terminals 1-2. The gate stops,
discontinuing the automatic closure cycle.
Use the keypad or the radio remote control
for the gate to resume movement.
Optional accessories
3W max. open gate pilot lamp connected
to 10-5. Lamp signals the gate's open
position. It turns off when the gate reaches
the closure end-stop.
2

GENERAL SPECIFICATIONS

Other functions
Automatic closure. The automatic closure
timer is self-powered in the aperture end-
stop. The adjustable time set in any case
depends on possible safety accessories
and is discontinued after a stop or when
there is no electricity.
Steady movement control. The gate remains
in function by keeping the key pressed (it
overrides the radio remote control function).
It is activated when the T.L. trimmer is set at
its minimum.
Adjustments
2nd motor closure delay time.
Automatic closure time.
Work time.
Warning! Turn off power supply before
opening the apparatus.
GB