CAME ZA3P 설치 매뉴얼 - 페이지 10
{카테고리_이름} CAME ZA3P에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. CAME ZA3P 13 페이지. Control panel for 230vgearmotors
CAME ZA3P에 대해서도 마찬가지입니다: 설치 매뉴얼 (13 페이지)
페이지 인쇄
Functions selection
Selector
1 ON Automatic closing enabled (1 OFF-disabled);
2 ON "Open-stop-close-stop" with button (2-7) and radio-control (AF card fi tted)
enabled;
2 OFF"Open-close" with button (2-7) and radio control (AF card fi tted) enabled; 3
ON "Only open" and radio control (AF card fi tted) enabled (3 OFF-disabled);
4 ON Pre-fl ashwhen opening and closing enabled (4 OFF- disabled);
5 ON Obstruction detection enabled (5 OFF-disabled);
6 OFF "Maintainedaction" (excludes the radio control from functioning) disabled (6
ON - enabled);
7 ON Final jolt enabled; at each opening and closing command, the gate leaves jolt inwards
for a second, to help release the electric lock connected to terminals 11-S. It is active
only if the leaves are closed at the end of the operating time, or at the fi rst maneuver after
powering up the system (7 OFF - disabled);
8 OFFTerminal CX enabled (8 ON - disabled);
9 ON Ten-second slow-down disabled (9 OFF - enabled );
10 ON Photocellstest enabled (10 OFF disabled).
Trimmer adjusting
OT = To set the operating time to a minimum of 10 seconds and a
maximum of 120 seconds.
ACT = To set the automatic closing time from a minimum of 1 second to a
maximum of 120 seconds.
TRM2= To set the closing delay on Motor 2 from a minium of 0 seconds to
a maximum of 15 seconds, and simultaneously the partial opening from a
minimum of 0 seconds to a maximum of 30 seconds.
Adjusting slow-down speed
For adjusting the slow-down speed (perform procedures only when gate is
stopped):
•
set DIP-switch 6 to ON;
•
by pressingCH 1, the red
speed (see table);
•
by againpressing CH 1 it shifts to the next speed;
•
confirmthe choice by pressing CH2;
•
resetDIP-switch 6 to OFF.
Adjusting the motor torque
To vary the motor torque, move the show faston to one of
the four positions:
1 min., 4 max..
LEDwill show the set slow-down
Selector
1 ON Limit switches enabled (1 OFF - disabled);
2 OFF CX withreclose while opening function;
2 ON CX with partialstop function.
Flashing in quick
succession
1
2
3
L2T
1
2
3
4
L1T
L2T
1
2
3
4
L1T
0
12 24
L1T
L2T
CT
0 12 24
2
FA1
FC1 FA2 FC2
L
N
U
V
W
X
Y
E E3
TS 10
10 11
S
1
2
3 3P 4
5
7
2 C1 CX B1 B2
L2T
1
2
3
4
L1T
0
12 24
L1T
L2T
CT
0 12 24
2
FA1
FC1 FA2 FC2
L
N
U
V
W
X
Y
E E3
TS 10
10 11
S
1
2
3 3P 4
5
7
2 C1 CX B1 B2
Slow-down
speed
minimum
medium
maximum
L2T
1
2
3
4
L1T
0
12 24
L1T
L2T
CT
0 12 24
2
FA1
FC1 FA2 FC2
L
N
U
V
W
X
Y
E E3
TS 10
10 11
S
1
2
3 3P 4
5
7
2 C1 CX B1 B2