CAME BK 1800 설치, 운영 및 유지보수 매뉴얼 - 페이지 9

{카테고리_이름} CAME BK 1800에 대한 설치, 운영 및 유지보수 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. CAME BK 1800 18 페이지. Sliding gate operator

F6 Maintained action

The gate opens and closes by keeping the button pressed. Opening button on contact 2-3 and closing button on contact 2-4. All other control

devices, even radio-based ones, are excluded.

F7 Command (2-7)

From the control device connected to 2-7 it performs the step-step (open-close-invert) or sequential (open-stop-close-stop) command.

F9 Obstruction detection with motor

idle

With the gate closed, opened or totally stopped, the gearmotor stays idle if the safety devices, that is, photocells or sensitive safety-edges detect

an obstruction.

F10 Gate-open signal output

It signals the gate status. The signal device is connected to contact 10-5.

F14 Sensor type selection

Setting the type of accessory for controlling the operator.

F18 Additional light

Extra light connection input on EX-W.

Outdoor light for additional visibility in the drive way.

Cycle: it stays lit from the moment the gate starts opening until it completely closes, including the automatic closing waiting time.

Courtesy: it stays on for an adjustable time of between 60 and 180 seconds. For adjusting the time, see function [F25].

F19 Automatic closing time

The automatic-closing wait starts when the opening limit switch point is reached and can be set to between 1 and 180 seconds. The automatic

closing does not activate if any of the safety devices trigger when an obstruction is detected, or after a total stop, or during a power outage.

F20 Automatic closing time after a

partial opening

The wait before the automatic closing starts after a partial opening command for an adjustable time of between 1 s and 180 s.

The automatic closing does not activate if any of the safety devices trigger when an obstruction is detected, or after a total stop, or during a power

outage.

F21 Preflashing time

Adjusting the pre-flashing time for the flashing light connected to E1-W, before each maneuver. The flashing time is adjustable from one to ten

seconds.

F25 Courtesy light time

Additional light that stays on for the required time during the when the gate is opening or closing.

EX-W contact output. It is adjustable between 60 seconds and 180 seconds.

F49 Managing serial connection

To enable the paired operating mode or the CRP (Came Remote Protocol).

F50 Save data

Saving users and saved settings in memory roll.

 This function only appears if a memory roll has been fitted into the control board.

F51 Read data

Uploading data saved in memory roll.

 This function only appears if a memory roll has been fitted into the control board.

F52 Passing parameter in paired

mode

Uploading settings from Master to Slave.

 It appears only if function [F49] is set to Paired.

F54 Opening direction

For setting the gate opening direction.

F56 Peripheral number

To set the peripheral's number from 1 to 255 for each control board when you have a system with several operators.

OFF (default) / ON

0 = Step-step (default) / 1 = Sequential

OFF (default) / ON

On when the barrier is open and moving (default)

during openings it flashes intermittently each half second

, and during closings it flashes intermittently each

second. It stays on steadily

when the barrier is open, off or when it s closed.

0 = control with transponder sensor or magnetic card reader.

1 = command with keypad selector (default).

OFF (default) / 1 = Cycle / 2 = Courtesy

OFF (default) / 1 = 1 second /... / 180 = 180 seconds

OFF / 1 = 1 second /.../ 10 = 10 seconds (default) /.../ 180 = 180 seconds

OFF (default) / 1 = 1 second /... / 10 = 10 seconds

60 = 60 seconds (default)/ 180 = 180 seconds

OFF (default) / 1 = Paired / 3 = CRP

OFF (default) / ON

OFF = Opening left (default) / ON = Opening right

1 ----> 255