Acoustic Research PW1000 빠른 시작 매뉴얼 - 페이지 3
{카테고리_이름} Acoustic Research PW1000에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Acoustic Research PW1000 6 페이지. Home theater power station with speed pass
페이지 인쇄with
Quick Start Guide
This Quick Start Guide helps you set
up your PW1000 in three quick and
easy steps:
Power /
SpeedPass
Charging /
Signal
Protection
It starts with a quick tour of the
PW1000 front and back panels.
SpeedPass makes it quick and easy to connect portable devices
SpeedPass
to your home theater by bringing connections for these devices
to the front of your home theater setup—but to use these front
panel connections, you must connect the corresponding jacks on
the back of the PW1000. This section shows you how.
SETUP
TABLET/
CAMCORDER
GAMING
PC/LAPTOP
SMARTPHONE
CONSOLE
Should I connect to my TV or my A/V receiver?
As a general rule, you should connect the PW1000 back panel jacks to the
component you use to switch signals. So, for example, if you use an A/V
receiver switch between your Blu-ray player and satellite receiver, then you
should connect the PW1000 back panel to your A/V receiver.
PW1000 QSG English 00
Front Panel
Front and back panel AC and USB power
Power /
outlets and coaxial jacks that provide
Charging /
Ethernet
surge protection and power conditioning
Signal
Protection
for connected components.
Switch
Note: The outlets and jacks on the front panel of the PW1000 are covered
by a door. To access these jacks and outlets, press down on this door.
To use the USB PASS THROUGH jack:
Use a USB cable (not included) to connect the
PW1000 back panel jack to your A/V receiver or TV.
TV or A/V Receiver
To use the HDMI PASS THROUGH jack:
Use an HDMI cable (not included) to connect the
PW1000 back panel jack to your A/V receiver or TV.
MP3 PLAYER/
SMARTPHONE
HDMI INPUT
Front panel audio/video jacks that pass
their signal through to corresponding
SpeedPass
back panel audio/video jacks. The
signal goes directly to the home theater
component that's connected to those
jacks.
To use the COMPONENT VIDEO and AUDIO jacks:
PW1000 Back Panel
2
OR
2
1
CMPNT INPUT
DIGITAL
AUDIO
VIDEO
COAX
USB IN
To use the MP3/AUDIO jack:
audio cable (not included) to connect the PW1000
back panel jack to your A/V receiver or TV.
PW1000 Back Panel
TV or A/V
TV or A/V
Receiver
Receiver
AUDIO
Back Panel
Network connectivity for your modem
Ethernet
and up to four connected Internet
Switch
devices. The input for your modem is
on the back panel, along with three of
the Ethernet output ports. The fourth
Ethernet output port is on the front
panel, for easy access by devices that
are just visiting your home theater.
PW1000 Back Panel
1. Make the video connection:
Use component video cables (not included) to connect the
PW1000 to your A/V receiver or TV.
2. Make the audio connection:
Use either a digital coaxial cable (not included) or a stereo
TV or A/V
audio cable (not included) to connect the PW1000 to your
Receiver
A/V receiver or TV—use the audio input grouped with the
component video jacks on your A/V receiver or TV.
To use the VIDEO and AUDIO jacks:
Use a stereo
1. Use a
video cable
(not included) to connect the PW1000 to your
A/V receiver or TV.
PW1000 Back Panel
2. Use a
stereo
audio cable
(not included)
to connect
the PW1000
to your A/V
receiver or TV.
P
Pa
PW1000 Back Panel
2
1
TV or A/V
Receiver
VID INPUT
R AUDIO L
VIDEO