Altox Timer-2 운영 매뉴얼 - 페이지 2

{카테고리_이름} Altox Timer-2에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Altox Timer-2 4 페이지.

페이지 인쇄

General Information

Dear buyers of ALTOX equipment!

We thank you for purchasing a new ALTOX TIMER-2. This device will provide

you with new convenient control options for your autonomous car parking

heater.

The time of automatic start of the heater can be set at any time of day

with an accuracy of 1 min (from 00:00 to 23:59). The user has three

programmable timers for the automatic start of the car parking heater,

each of which can be set to work in single-start mode for the day ahead or

in the weekly mode for 7 days ahead.

The operating time of the parking heater for each timer can be set in the

range from 10 to 99 minutes.

Using the device

ALTOX TIMER-2 is used for programming and controlling the operation of

Eberspacher and Webasto Thermo Top car parking heaters, using a digital

signal (E-Bus and W-Bus), as well as any other aftermarket car parking

heaters with an analogue signal.

ALTOX TIMER-2 has a built-in INPUT, which allows you to connect additional

automotive equipment to expand the management capabilities of your

heater. For example, for controlling the parking heater using the car alarm

control panel.

Switching the device on

After the power is applied, the display shows all the characters or the

current operating mode of the device: "P1" or "P2", if it is activated

(description of the operating modes below).

To navigate through the sections of the menu, 4 buttons are available to

the user.

The switched-on display, regardless of the active menu section, when no

buttons are pressed, automatically turns oﬀ after 60 seconds, after which

the device switches to standby mode after 1min.

Brightness adjustment

In the standby mode (the display is oﬀ), you must press the "<" or ">"

button to enter the current time display menu, then press and hold the ">"

button and then press "P".

The display shows the current brightness value of the display from 10 to 99

"L: XX", the customizable symbol ﬂashes.

Set the desired value by pressing the "<" and ">" buttons.

The entered value is stored after pressing the "P" button.

Operating modes of the device

The user has three modes of operation depending on the type of

installation of the car parking heater.

Changing the modes of the mini-timer is done by the slide switch, which is

located in the upper part of the device case.

After changing the position of the switch, the name of the selected mode

is displayed:

Р0 — the control mode of a factory-installed parking heater.

In this mode, the OUT output is switched on with a delay of 1/2 from the

running time of the heater or when the heater temperature reaches 50°C

and switches oﬀ with the heater (used to start and stop the climate

control of the car).

Р1 — the control mode of the aftermarket parking heater when the vehicle

is retroﬁtted with this equipment. In this mode, the OUT output is

switched on together with the heater, and turns oﬀ with a delay of 1

minute after the heater is turned oﬀ to control the coolant circulation

pump using a power relay.

Р2 — the "pre-heater" mode for controlling the parking heater after the

vehicle is retroﬁtted with this equipment. In this mode, the mini-timer

turns on the heater automatically at each start-up of the vehicle,

according to the supply voltage (above 13.2 V for 10 seconds). Switching

oﬀ the heater occurs after the car engine has stopped to reduce the

voltage (below 13.2V for 10sec). In this mode, the OUT output operates as

in P1 mode and is designed to control the coolant circulation pump using a

power relay.

Additional functions

Optionally, the mini-timer supports working together with other

Eberspacher and Webasto Thermo Top parking heaters controls units via a

digital bus (E-Bus or W-Bus). This function allows you to turn the car

parking heater on from one device and turn it oﬀ from another device.

After the digital signal of the other control unit has been determined,

"TELE" appears on the mini-timer display.

Optionally, the mini-timer supports the unlocking function of the factory

installed Webasto Thermo Top parking heater on Volkswagen Transporter T5

and T5 GP cars without the use of diagnostic equipment. To clarify the

presence of this function in your device, you need to contact the service

center.

Note: the unlocking function is used only in the heaters installed by the

manufacturer in the previously mentioned car brands, in all other heaters,

the unlocking is done by removing errors.