Altox Timer-2 Kullanım Kılavuzu - Sayfa 2

Zamanlayıcı Altox Timer-2 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Altox Timer-2 4 sayfaları.

Sayfayı Yazdır
General Information
Dear buyers of ALTOX equipment!
We thank you for purchasing a new ALTOX TIMER-2. This device will provide
you with new convenient control options for your autonomous car parking
heater.
The time of automatic start of the heater can be set at any time of day
with an accuracy of 1 min (from 00:00 to 23:59). The user has three
programmable timers for the automatic start of the car parking heater,
each of which can be set to work in single-start mode for the day ahead or
in the weekly mode for 7 days ahead.
The operating time of the parking heater for each timer can be set in the
range from 10 to 99 minutes.
Using the device
ALTOX TIMER-2 is used for programming and controlling the operation of
Eberspacher and Webasto Thermo Top car parking heaters, using a digital
signal (E-Bus and W-Bus), as well as any other aftermarket car parking
heaters with an analogue signal.
ALTOX TIMER-2 has a built-in INPUT, which allows you to connect additional
automotive equipment to expand the management capabilities of your
heater. For example, for controlling the parking heater using the car alarm
control panel.
Switching the device on
After the power is applied, the display shows all the characters or the
current operating mode of the device: "P1" or "P2", if it is activated
(description of the operating modes below).
To navigate through the sections of the menu, 4 buttons are available to
the user.
The switched-on display, regardless of the active menu section, when no
buttons are pressed, automatically turns off after 60 seconds, after which
the device switches to standby mode after 1min.
Brightness adjustment
In the standby mode (the display is off), you must press the "<" or ">"
button to enter the current time display menu, then press and hold the ">"
button and then press "P".
The display shows the current brightness value of the display from 10 to 99
"L: XX", the customizable symbol flashes.
Set the desired value by pressing the "<" and ">" buttons.
The entered value is stored after pressing the "P" button.
Operating modes of the device
The user has three modes of operation depending on the type of
installation of the car parking heater.
Changing the modes of the mini-timer is done by the slide switch, which is
located in the upper part of the device case.
After changing the position of the switch, the name of the selected mode
is displayed:
Р0 — the control mode of a factory-installed parking heater.
In this mode, the OUT output is switched on with a delay of 1/2 from the
running time of the heater or when the heater temperature reaches 50°C
and switches off with the heater (used to start and stop the climate
control of the car).
Р1 — the control mode of the aftermarket parking heater when the vehicle
is retrofitted with this equipment. In this mode, the OUT output is
switched on together with the heater, and turns off with a delay of 1
minute after the heater is turned off to control the coolant circulation
pump using a power relay.
Р2 — the "pre-heater" mode for controlling the parking heater after the
vehicle is retrofitted with this equipment. In this mode, the mini-timer
turns on the heater automatically at each start-up of the vehicle,
according to the supply voltage (above 13.2 V for 10 seconds). Switching
off the heater occurs after the car engine has stopped to reduce the
voltage (below 13.2V for 10sec). In this mode, the OUT output operates as
in P1 mode and is designed to control the coolant circulation pump using a
power relay.
Additional functions
Optionally, the mini-timer supports working together with other
Eberspacher and Webasto Thermo Top parking heaters controls units via a
digital bus (E-Bus or W-Bus). This function allows you to turn the car
parking heater on from one device and turn it off from another device.
After the digital signal of the other control unit has been determined,
"TELE" appears on the mini-timer display.
Optionally, the mini-timer supports the unlocking function of the factory
installed Webasto Thermo Top parking heater on Volkswagen Transporter T5
and T5 GP cars without the use of diagnostic equipment. To clarify the
presence of this function in your device, you need to contact the service
center.
Note: the unlocking function is used only in the heaters installed by the
manufacturer in the previously mentioned car brands, in all other heaters,
the unlocking is done by removing errors.