djm direct DJMSL8 원본 운영 매뉴얼 번역 - 페이지 7

{카테고리_이름} djm direct DJMSL8에 대한 원본 운영 매뉴얼 번역을 온라인으로 검색하거나 PDF를 다운로드하세요. djm direct DJMSL8 14 페이지.

페이지 인쇄

Remove all packaging material from the machine and the accessories

provided.

Before starting the operation of the machine for the first time, check

if all parts listed in the box content section have been supplied

Note: Check the power tool for possible damage. Before further use

of the machine, check that all protective devices are fully functional.

Any lightly damaged parts must be carefully checked to ensure

flawless operation of the tool. All parts must be properly mounted

and all conditions fulfilled that ensure faultless operation.

Damaged protective devices and parts must be immediately replaced

by an authorised service centre.

Always tighten the locking knob (20)&(12) firmly before

sawing.

Otherwise the saw blade can become wedged in the workpiece.

Transportation

Lift the mitre saw only when the saw arm is locked in the down

position, the saw is switched off and the plug is removed from the

power point.

Only lift the saw by the operating handle (5) or outer castings. Do not

lift the saw using the guards.

Stationary or Flexible Mounting

To ensure safe handling, the machine must be mounted on a level

and stable surface (e. g., workbench) prior to using.

Mounting to a Working Surface

– Fasten the power tool with suitable screw fasteners to the working

surface. The mounting holes serve for this purpose.

– Clamp the power tool with commercially available screw clamps by

the feet to the working surface.

Mounting to a Saw Stand

Any universal saw stand which will accept mounting holes 420mm

wide by 350mm in length will suffice

Read all safety warnings and instructions included with the

worktable. Failure of observing safety warnings and instructions can

lead to electrical shock, fire and/or cause serious injuries.

Assemble the worktable properly before mounting the power tool.

Perfect assembly is important in order to prevent the risk of

collapsing.

– Mount the power tool in transport position on the saw stand.

Dust/Chip Extraction

Dusts from materials such as lead-containing coatings, some wood

types, minerals and metal can be harmful to one's health. Touching

or breathing-in the dusts can cause allergic reactions and/or lead to

respiratory infections of the user or bystanders.

Certain dusts, such as oak or beech dust, are considered as

carcinogenic, especially in connection with wood-treatment additives

(chromate, wood preservative). Materials containing asbestos may

only be worked by specialists.

– Always use dust extraction or the Dust bag (11) provided

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the materials to

be worked.

The dust/chip extraction can be blocked by dust, chips or workpiece

fragments.

– Switch the machine off and pull the mains plug from the socket

outlet.

– Wait until the saw blade has come to a complete stop.

– Determine the cause of the blockage and correct it.

Integrated Dust Extraction.

– Insert the dust bag firmly onto the machine

During sawing, the dust bag must never come in contact with moving

tool components.

Always empty the dust bag in good time.

External Dust Extraction

For dust extraction, you can also connect the extraction port to a

vacuum hose (internal Ø 40 mm).

The dust extractor must be suitable for the material being worked.

When vacuuming dry dust that is especially detrimental to health or

carcinogenic, use a special dust extractor.

Changing the Blade

–Make sure that the electrical plug is removed from the power point.

–Push down on the operating handle (3) and pull there lease knob (4)

to disengage the saw arm (3).

–Raise the saw arm (3) to its highest position.

–Loosen the cover plate screw about 2 turns with a Phillips

screwdriver. Do not remove this screw from the tool.

–Pull the rotating blade guard (8) down. When the rotating blade

guard (8) is positioned over the upper fixed blade guard (6) it is

possible to access the blade bolt.

–Lift and hold up the lower blade guard (8) to expose the threaded

blade bolt.

–Hold the rotating guard (8) up and press the spindle lock button

(22). Rotate the blade until the spindle locks.

–Use the 6 mm hex key provided to loosen and remove the blade

bolt. (Loosen in a clockwise direction as the blade screw has a left

hand thread).