FLAVIA SB100 사용자 설명서 - 페이지 10
{카테고리_이름} FLAVIA SB100에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. FLAVIA SB100 11 페이지. Brewer
FLAVIA SB100에 대해서도 마찬가지입니다: 사용자 설명서 (14 페이지)
페이지 인쇄
Trouble shooting
If...
Water is not heating.
The amount of water
dispensed is too small and/or
is dripping too slowly.
The walls of the tank have
changed color, there is a milky
white layer floating on top of
the water in the tank and/or the
sound of the water when
heating is louder than is usual.
The taste of beverages and
hot water from the appliance
have deteriorated.
Beverages and hot water from
the appliance have an unpleasant
odour.
Beverages and heated water
are not hot enough.
■ When making a beverage
The appliance is not operating
after inserting a beverage
filterpack in the filterpack holder.
(
is lit)
The appliance makes a 'pop' sound
when the start button is pressed
to start making a beverage.
■ When dispensing hot water
Cannot release the lock.
Hot water won't dispense.
Hot water stops coming out when
the
key is pressed.
■ In case you see the following
indicators
is lit
Both
and
are lit
■ If the following indicators are on, the appliance is malfunctioning.
Two lights are on simultaneously
and
and
and
If the problem is not fixed after checking the above given possible causes, pull the plug out of the socket and contact your lo cal Flavia
Beverage System supplier.
Before calling a service supplier,
please check the following possible causes.
P
o
s s
b i
e l
a c
u
s
e
• The plug may be loose in the socket.
• The power switch may be in the OFF position.
• The mesh filter may be blocked
i w
h t
c s
l a
. e
• The tank and internal parts through which
water flows are blocked with scale.
• Just before and after finishing heating the
delivered volume may be low.
• The cause of this are scale deposits.
* Water with a large content of minerals in it such
as mineral water or ionised water, is more likely
to cause a change of color and/or the appearance
of a white layer on the surface of the water.
• The carbon filter may need replacing.
• Purifying agents in the water supply can leave traces of odour.
• When the appliance is new, resin used in manufacture may give off a mild odour. This will
disappear with use.
• If the appliance is placed on surfaces such as a vinyl sheet, the odour may be carried over into the water.
• The separator may not be properly inserted.
• Fresh water has been added to the tank in
Keep warm mode immediately before making
a
b
e
e v
a r
g
. e
• Allow approximately 15 seconds for the
beverage to be dispensed.
• On the
setting, the filterpack is filled with
air which makes the 'pop' sound.
When the
light is green, the lock cannot be released.
A used beverage filterpack may have been left in the
filterpack holder. The 'Remove-filterpack' light is on)
The lock may not have been released.
The start button may be raised, and/or the
filterpack holder may be open.
When pressed once and held down, the amount of hot water dispensed is equal to approximately 8oz
Water supply indicator is working
• Make sure that the appliance has been filled
with water before turning the power switch on.
• The level of water in the tank may be low.
This may occur temporarily when water is
poured into the tank.
Please contact your local Flavia
Beverage System supplier.
®
Advise the supplier which lights are on.
7
9
H
o
w
o t
f
x i
Firmly insert the plug in the socket.
Put the power switch in the ON position.
Clean the mesh filter with a brush once every
t
w
o
m
o
n
h t
. s
S (
e
e
p
a
g
e
4
&
) 6
If this brings no improvement, please
change the filter. (See the back cover)
Please contact your local Flavia
®
Beverage System Supplier.
This is perfectly normal.
Please contact your local Flavia
®
Beverage System Supplier.
Please replace the carbon filter once a year.
(See back cover)
Correct position of the separator. (See page 4)
To make a beverage, please wait for the green
light
to come on. For hot water, please wait
f
r o
h t
l e
g i
t h
o t
g
o
o
. f f
? Press the start button and open the filterpack
holder.
? Re-select the desired beverage setting.
? Close the filterpack holder and press the start button .
This is perfectly normal
Remove the filterpack from the filterpack holder.
close the filterpack holder and lower the start
button into its original position.
Press the
key. The light will come on
* After the light goes off, the lock will be auto-
matically reset after approximately 10 seconds
Close the filterpack holder and lower the
start button into its original position.
Fill with water.
Make sure the tank is filled with water. Turn
the power switch off and turn it back on after
10 seconds.
®