Etabeta electronics NT-16 사용 설명서 - 페이지 9
{카테고리_이름} Etabeta electronics NT-16에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Etabeta electronics NT-16 18 페이지.
페이지 인쇄Features - Front panel
11. Push mode button (signal routing)
1). Main key in push mode
When the MAIN light is on, it means that the current push is at the push level of the corresponding channel, and this level is
controlled by the push level of the corresponding channel.
Long press this button to lock the mixer. At this time, the channel parameters will not be adjusted. Long press again to unlock.
2). AUX1-AUX4 output by pushing mode button
When the page-turning button IN is lit, press the AUX button to flash, and the pusher is IN the signal level state sent from the
input channel to the corresponding AUX auxiliary output.
The transmission size is controlled by the pushers of the corresponding channel.
3). Push mode button FX1 / FX2
When the page-turning button IN is lit, press the FX1-FX2 indicator light flashes, and the pusher is IN the input channel and
sends to the signal level corresponding to FX1-FX2.
The send size is controlled by the push of the current channel.
4). Tap effect tempo button
Effect 1: Short delay in delay Long delay is the metronome effect,
Effect 2: Delay click the Tap button to change the echo delay time of the speed effect in a short delay.
12. input/output channel push page turning button
1).GEQ- When the output channel is selected, this button is effective. When the button is turned on, the push is in control of the
gain of 12 segments of the output equalizer
2). In - When this button is on, the push controls the channel level (CH1-CH12) corresponding to the input channel of the first
layer.
3).OUT- When this button is on, the push controls the corresponding level size of the second channel (ST stereo, digital
channel, FX1, FX2, SUB grouping output and AUX auxiliary output).
13. Quick call button in scene mode
Click the corresponding button to quickly call up the first four modes of the scene mode.
14. + 48V switch/multi-function knob
1).48V phantom power button
Long press the button for 3 seconds to turn on the 48V power supply of the current channel and light it, indicating that the MIC
jack has 48V voltage.
Note: Do not turn on the phantom power until you have connected the microphone.
2). Multi-function knob
Touch this knob to adjust the parameters with the display screen.
15. input and output monitoring signal indicator light.
16. Stereo input channel
1).SEL channel selection key
The button lights up to indicate that a channel has been selected and that channel parameters can be edited.
2).ON mute switch
Stereo channel mute switch, off means that the stereo channel is in dumb state, you will not hear the signal of the channel
3).PFL monitor switch
When this button is pressed, the signal will be output from the listener and the headset.
4). Volume knob
This knob currently controls the volume of the stereo channel and can also be controlled by the stereo pusher on the second
layer of the pusher (out).
17. digital input channel (MP3/ sound card control)
1).SEL channel selection key
The button lights up to indicate that a channel has been selected and that channel parameters can be edited.
2).ON mute switch
Digital channel mute switch, when off the channel will be in mute state, you will not hear the signal of the channel
3).PFL monitor switch
When this button is pressed, the signal will be output from the listener and the headset.
4). Volume knob
This knob currently controls the volume of the digital channel and can also be controlled by the digital channel push of the
second layer of the push layer (OUT).
18. MP3 operation area
1). Disp - When the USB flash drive is inserted, the system will automatically recognize the USB flash drive. Click this button to
enter the page of the MP3 player.
2).rec - When this button is flashing, recording is in progress, and when it is not flashing, recording is paused.
Previous, Pause/Play, Next
19. System key area (ESC,COPY, MODE, SYS keys)
1).ESC button: Click this button to return the LOGO page.
2). Copy button: When entering the channel page, long press this button to pop up the channel COPY page. Select the channel
to be copied to and click this button again
Button to copy the parameters of the previous channel to the corresponding channel..
3). Mode button: Click this button to enter the scene MODE page for storing and calling the scene.
4).SYS system button: Click this button to enter the system setting page, language setting, network setting, version information
and software update and other operations.
20. Touch screen
8