Cynergy3 IWTxT-000 운영 매뉴얼 - 페이지 10

{카테고리_이름} Cynergy3 IWTxT-000에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cynergy3 IWTxT-000 11 페이지. Wireless transmitter with tx supply adds wireless functionality to any 4-20 ma transmitter

페이지 인쇄

| IWTxT SERIES

WIRELESS 4-20mA TRANSMITTER OPERATING MANUAL

This equipment has been tested and found to comply with the limits for a Class B device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy, and if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver

•

Connect the equipment into an outlet on a circuit different from that which the receiver is

•

connected

•

Consult the dealer or an experienced radio/TV technician for help

Warning: Changes or modifications not expressly approved by Cynergy3 could void the user's authority to

operate the equipment.

RF Exposure

Contains FCC ID: W70MRF24J40MDME

In this equipment, the antenna supplied is a PCB antenna and an alternative antenna must not be used.

Caution: To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a

separation distance of 20cm or more should be maintained between the antenna of this device and

persons during operation. To ensure compliance operation at closer than this distance is not

recommended. The antenna used for this transmitter must not be co-located or operating in conjunction

with any other antenna or transmitter. No other antenna may be used with this equipment other than the

PCB antenna supplied with this equipment.

Canada (IC)

English

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of the type

and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

French

Le présent appareil est conforme aux CNR d'industrie Canada applicables aux appareils radio exempts de

licence. L'explitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de

brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage, et (2) l'utilisateur de l'appareil doit

accepter tout brouillage radioelectrique subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec

une antenna d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.

Dans le but de réduire les risques de brouillage radioélectrique à I'intention des autres utilisateurs, il fait

choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e) ne

dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Page 10