AMD DIrect SSRFR-24DR2 User Manual - Page 6

Browse online or download pdf User Manual for Refrigerator AMD DIrect SSRFR-24DR2. AMD DIrect SSRFR-24DR2 9 pages. 2-drawer refrigerator

Print Page

OPERATING YOUR APPLIANCE

It is recommended that you install the appliance

in a place where the ambient temperature is

between 50°F and 109.4°F (10°C-43°C). If the ambient

temperature is above or below recommended

temperatures, the performance of the unit may

be affected. For example, placing your unit in

extremely cold or hot conditions may cause interior

temperatures to fluctuate. The operating temperature

range may not be reached.

CONTROL PANEL

ON/OFF POWER

To turn the appliance ON or OFF, press and hold the

POWER key

for 5 seconds.

AND DOWN

Press

first, then press

button

SET

to increase (warm) or decrease (cool) the set

temperature by 1°C/ 1°F.

Press

again, the temperature is selected and

SET

shows the actual temperature. If no other further

operation in 6 seconds, display will show actual

temperature in the cooler

°F/°C SELECTOR

Selects the temperature display setting in Fahrenheit

or Celsius degrees. To change the temperature from

Fahrenheit to Celsius or from Celsius to Fahrenheit,

press

and

at the same time, then hold for 6

SET

seconds.

SETTING THE TEMPERATURE CONTROL

The temperature you are setting will increase by

one degree each time you press the

key and

will decrease by one degree each time you press

the

key.

The range of temperature control is from 32°F to 50°F.

To view the set temperature at any time, press

the

key. The set temperature will flash in the

SET

display window for 6 seconds. After 6 seconds, the

temperature inside the until will reappear in the

display window.

(The temperature preset at the factory is 36°F)

2-DRAWER REFRIGERATOR USER MANUAL

INSTALLATION OF YOUR APPLIANCE

This appliance has been designed for both built-in

and freestanding applications. When built-in, the

refrigerator drawers do not require additional air

space for top, side or rear. The front grille must not

be obstructed.

NOTE:

It is recommended that you do not install the

appliance near an oven, radiator or other heating

source, as heat sources may increase electrical

consumption. Do not install in a location where the

temperature will fall below 50°F (10°C). For best

performance, do not install the appliance behind

a cabinet door or block the base grille. Plug the

appliance into an exclusive properly grounded wall

outlet.

SITE PREPARATION

1. Position the unit on a flat, level surface capable

of supporting the entire weight of the unit.

Remember the unit will be significantly heavier

once it is fully loaded.

2. Connect the unit to a Ground Fault Interrupter

(GFI).

3. The unit must be installed according to your local

codes and ordinances.

4. ELECTROCUTION HAZARD!

• Electrical Grounding Required - This appliance

is equipped with a 3-prong (grounding)

polarized plug for your protection against

possible shock hazards.

• NEVER remove the round grounding prong

from the plug.

• NEVER use a 2-prong grounding adapter.

• NEVER use an extension cord to connect power

to the unit.

• Where a 2-prong wall receptacle is

encountered or a longer power cord is

required, contact a qualified electrician to

have it replaced in accordance with applicable

electrical codes.

• NEVER use an extension cord to connect power

to the unit.

• Where a 2-prong wall receptacle is

encountered or a longer power cord is

required, contact a qualified electrician to

have it replaced in accordance with applicable

electrical codes.

INSTALLATION

1. Position the unit to allow free air flow through the

front grille.

2. Wipe out inside of the unit with a damp cloth.

3. Be sure to install the Anti-Tip Bracket. Follow

instructions provided with the Anti-Tip bracket.

The Anti-Tip bracket must

be installed on this unit

before it is used. Double

stacking units may cause

serious personal injury.

ANTI-TIP BRACKET INSTALLATION

To reduce the risk of tipping the unit by abnormal

usage or improper loading, the appliance must be

secured by properly installing the anti-tip device

packed with the appliance.

• Place the anti-tip bracket on the floor as shown in

the figure. An anti-tip device can be installed on

either the right of left side.

• Mark the locations of the 4 holes of the anti-tip

bracket on the floor.

• Use a 5/16 masonry drill bit and insert plastic

anchors.

• Secure bracket to floor using screws.

• Slide appliance into position and make sure the

leg engages the anti-tip bracket.

NOTE:

If the unit is relocated, the bracket must be removed

and installed in the new location.

LEVELING THE UNIT

Position the unit on a flat, level surface capable of

supporting the entire weight of the unit when full. The

unit contains four (4) adjustable leveling legs. Turn

the leg's clockwise to raise and counterclockwise

to lower.

INSTALLING THE HANDLE

Install the handle on the drawer if not already

attached. Put the screws on top of the drawer where

the handle is to be installed. Align the handle with

screws, tighten the screws using the screwdrivers.