AMD DIrect SSRFR-24DR2 Kullanıcı Kılavuzu - Sayfa 6
Buzdolabı AMD DIrect SSRFR-24DR2 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. AMD DIrect SSRFR-24DR2 9 sayfaları. 2-drawer refrigerator
Sayfayı Yazdır
OPERATING YOUR APPLIANCE
It is recommended that you install the appliance
in a place where the ambient temperature is
between 50°F and 109.4°F (10°C-43°C). If the ambient
temperature is above or below recommended
temperatures, the performance of the unit may
be affected. For example, placing your unit in
extremely cold or hot conditions may cause interior
temperatures to fluctuate. The operating temperature
range may not be reached.
CONTROL PANEL
ON/OFF POWER
To turn the appliance ON or OFF, press and hold the
POWER key
for 5 seconds.
UP
AND DOWN
Press
first, then press
or
button
SET
to increase (warm) or decrease (cool) the set
temperature by 1°C/ 1°F.
Press
again, the temperature is selected and
SET
shows the actual temperature. If no other further
operation in 6 seconds, display will show actual
temperature in the cooler
°F/°C SELECTOR
Selects the temperature display setting in Fahrenheit
or Celsius degrees. To change the temperature from
Fahrenheit to Celsius or from Celsius to Fahrenheit,
press
and
at the same time, then hold for 6
SET
seconds.
SETTING THE TEMPERATURE CONTROL
The temperature you are setting will increase by
one degree each time you press the
key and
will decrease by one degree each time you press
the
key.
The range of temperature control is from 32°F to 50°F.
To view the set temperature at any time, press
the
key. The set temperature will flash in the
SET
display window for 6 seconds. After 6 seconds, the
temperature inside the until will reappear in the
display window.
(The temperature preset at the factory is 36°F)
3
2-DRAWER REFRIGERATOR USER MANUAL
INSTALLATION OF YOUR APPLIANCE
This appliance has been designed for both built-in
and freestanding applications. When built-in, the
refrigerator drawers do not require additional air
space for top, side or rear. The front grille must not
be obstructed.
NOTE:
It is recommended that you do not install the
appliance near an oven, radiator or other heating
source, as heat sources may increase electrical
consumption. Do not install in a location where the
temperature will fall below 50°F (10°C). For best
performance, do not install the appliance behind
a cabinet door or block the base grille. Plug the
appliance into an exclusive properly grounded wall
outlet.
SITE PREPARATION
1. Position the unit on a flat, level surface capable
of supporting the entire weight of the unit.
Remember the unit will be significantly heavier
once it is fully loaded.
2. Connect the unit to a Ground Fault Interrupter
(GFI).
3. The unit must be installed according to your local
codes and ordinances.
4. ELECTROCUTION HAZARD!
• Electrical Grounding Required - This appliance
is equipped with a 3-prong (grounding)
polarized plug for your protection against
possible shock hazards.
• NEVER remove the round grounding prong
from the plug.
• NEVER use a 2-prong grounding adapter.
• NEVER use an extension cord to connect power
to the unit.
• Where a 2-prong wall receptacle is
encountered or a longer power cord is
required, contact a qualified electrician to
have it replaced in accordance with applicable
electrical codes.
• NEVER use an extension cord to connect power
to the unit.
• Where a 2-prong wall receptacle is
encountered or a longer power cord is
required, contact a qualified electrician to
have it replaced in accordance with applicable
electrical codes.
INSTALLATION
1. Position the unit to allow free air flow through the
front grille.
2. Wipe out inside of the unit with a damp cloth.
3. Be sure to install the Anti-Tip Bracket. Follow
instructions provided with the Anti-Tip bracket.
The Anti-Tip bracket must
be installed on this unit
before it is used. Double
stacking units may cause
serious personal injury.
ANTI-TIP BRACKET INSTALLATION
To reduce the risk of tipping the unit by abnormal
usage or improper loading, the appliance must be
secured by properly installing the anti-tip device
packed with the appliance.
• Place the anti-tip bracket on the floor as shown in
the figure. An anti-tip device can be installed on
either the right of left side.
• Mark the locations of the 4 holes of the anti-tip
bracket on the floor.
• Use a 5/16 masonry drill bit and insert plastic
anchors.
• Secure bracket to floor using screws.
• Slide appliance into position and make sure the
leg engages the anti-tip bracket.
NOTE:
If the unit is relocated, the bracket must be removed
and installed in the new location.
LEVELING THE UNIT
Position the unit on a flat, level surface capable of
supporting the entire weight of the unit when full. The
unit contains four (4) adjustable leveling legs. Turn
the leg's clockwise to raise and counterclockwise
to lower.
INSTALLING THE HANDLE
Install the handle on the drawer if not already
attached. Put the screws on top of the drawer where
the handle is to be installed. Align the handle with
screws, tighten the screws using the screwdrivers.
4