American Standard YORKVILLE 2878.100 Installation Instructions - Page 3

Browse online or download pdf Installation Instructions for Toilets American Standard YORKVILLE 2878.100. American Standard YORKVILLE 2878.100 4 pages. 1.1 gpf two-piece pressure-assisted toilets, 1.1 gpf two-piece pressure-assisted toilets

Print Page

TANK MTG.

BOLTS

WASHER

NUT

Before continuing, determine the type of water supply connecation you have from

the chart below and use the appropriate assembly parts required to properly

reconnect the water supply. DO NOT use plumber's putty to seal these fittings.

METAL/COPPER

FLARED TUBING

LOCK NUT

CONE

WASHER

COUPLING

NUT

WATER

SHUT-OFF

These parts must be used as

illustrated to insure water-tight

connection. Use of existing

coupling nut may result in water

leakage. Water supply tube or pipe

must extend at least 1/2" inside

threaded shank of valve (does not

apply to flanged tubing).

CAUTION: DO NOT USE

CONE WASHER WITH

PLASTIC SUPPLY LINE.

Repair parts are determined by toilet tank number which can be found marked inside tank.

NOTE: "XXX" represents color or trim finish options. Specify when ordering.

PART NO.

7381051-200

7381065-200

4142-100.XXX

4142.801.XXX

735133-400.XXX

3481.100.XXX

3483.100.XXX

3701.100.XXX

3703.100.XXX

034783-XXX0A

034602-0070A

7381054-100

7381053-100

7381052-100

7301320-100

034783-XXX0A

735133-401.XXX

603111-0030A

INSTALL TANK

a. Install large rubber gasket over threaded outlet

on bottom of tank and lower tank onto bowl so that

tapered end of gasket fits evenly into bowl

water inlet opening, and tank mounting bolts go

SPONGE

WASHER

through mounting holes. Secure with metal

washers and nuts.

b. With tank parallel to wall, alternately tighten

nuts until tank is snugged down evenly against

bowl surface.

CAUTION: DO NOT OVERTIGHTEN

NUTS MORE THAN REQUIRED

METAL FLANGED

METAL SPIRAL

TUBING

LOCK NUT

EXISTING

WASHER

EXISTING

COUPLING

NUT

WATER

SHUT-OFF

Use existing

Use existing spiral cone

coupling nut

washer. Fluidmaster

and washer.

cone washer may not

seal completely on

spiral type supply line.

CAUTION: Overtightening of

LOCK NUT or COUPLING NUT

could result in breakage and

potential flooding.

REPAIR PARTS LIST

DESCRIPTION

TRIP LEVER ASSEMBLY LH

TRIP LEVER ASSEMBLY, WDI PRESSURE ASSIST, RH

TANK (COMPLETE WITH COUPLING COMPONENTS AND TANK TRIM)

TANK (COMPLETE WITH COUPLING COMPONENTS AND RH TANK TRIM)

TANK COVER

BOWL, ELONGATED 15"

BOWL, ELONGATED 16-1/2"H

BOWL, ELONGATED 15"

BOWL, ELONGATED 16-1/2" (419mm)

BOLT CAP COVER KIT (INCL TWO COVERS/WASHERS)

COUPLING GASKET

LOWER SUPPLY ASSEMBLY

UPPER SUPPLY ASSEMBLY

VALVE CARTRIDGE ASSEMBLY

TANK COUPLING KIT

BOLTS AND CAPS

TANK COVER FOR LOCKING DEVICE

COVER LOCKING DEVICE KIT

FOR A SNUG FIT!

VINYL/BRAIDED

CONNECTOR

LOCK NUT

EXISTING

COUPLING

CONE

NUT

WASHER

COUPLING

NUT

WATER

SHUT-OFF

Captive cone

washers already

included. No

additional

washers needed.

- 3 -

INSTALL TOILET SEAT

Install toilet seat in accordance

with manufacturer's directions.

ADJUSTMENTS

The flushometer tank is designed and

factory-adjusted to provide a

consistent, safe seal depth in the

bowl after each flush. Field refill

adjustment is not required. The refill

has been preset and locked.

TOILET

73 01276 - 10 0 Rev. A