Ekinex EK-EH2-TP-RW Quick Start Manual - Page 2

Browse online or download pdf Quick Start Manual for Recording Equipment Ekinex EK-EH2-TP-RW. Ekinex EK-EH2-TP-RW 4 pages. 6-fold knx pushbutton

Print Page

Rockers

Three-positions rockers with central neutral position have

to be mounted on the pushbutton. Pushing one side of

a rocker (for example the upper one), the pushbutton

sends on the bus a telegram for switching on, increasing

the brightness of luminaires or raising the blinds, while

pushing the other side (for example the lower one), it sen-

ds a telegram for switching off, reducing the brightness of

luminaires or lowering the blinds. Each channel is equip-

ped with LEDs which can be freely programmed as status

feedbacks of the loads and as orientation nightlight.

Code *

Material

EK-TQQ-GAx

plastic

EK-TQQ-GBx

metal

EK-TRO-GAx

plastic

EK-TRO-GBx

metal

(*) It has to be completed with the extension for the colour choosed (x)

Note. The application program allows to configure

the pushbutton with a combination of square and

rectangular rockers. For the allowed combinations

see the application manual or the application pro-

gram for ETS.

Customization of rockers

The rockers can be customized with symbols and texts,

for more information see the standard library on the eki-

nex

catalog or the website www.ekinex.com. On request

it is also possible a customization with symbols and texts

chosen by the customer.

Frame

The device is completed with a rectangular frame of the

form (EK-FOR-...) or flank (EK-FLR-...) series.

Code *

Material

EK-FOR-GAx

plastic

EK-FOR-GBx

metal

EK-FLR-GAx

plastic

EK-FLR-GBx

metal

(*) It has to be completed with the extension for the colour (x)

Mounting

The device has degree of protection IP20, and is therefo-

re suitable for use in dry interior rooms. The installation of

the device requires the following steps:

a) fix the metallic support (5) with the screws supplied

(6) on the wall box (7) provided with suitable fixing holes;

b) snap a rectangular frame (4) of the form or flank series,

inserting it from the rear of the device (3);

c) enter the bus terminal, previously connected to the bus

cable in its slot on the rear side (see also: "Connection

of the KNX bus line"). At this point it is recommended to

carry out the commissioning of the device (see also "Con-

figuration and commissioning") or at least the download of

the physical address;

Modularity

Package

[mm]

4 pcs.

40 x 40

square

4 pcs. rec-

80 x 20

tangular

Dimens.

Package

[mm]

1 pcs.

126 x 86

1 pcs.

135 x 80

1) Rockers (to be ordered separately)

2) Screws to fasten the pushbutton on the metallic support

3) 6-fold pushbutton

4) Frame of the series form or flank (to be ordered separately)

5) Metallic support for mounting wall box

6) Screws for fixing the support on the wall box

7) Flush-mounting box

d) mounting the device (3) on the metallic support sup-

plied (5) with the screws (2). The correct mounting of the

device occurs when the bus terminal is located in the lo-

wer part; for mounting the device follow also the indication

TOP (arrow tip pointing up) on the rear side of the device.

e) snap the six rockers (1) on the device.

The 6-fold pushbutton can be mounted on a round or a

square (60 mm hole centres) or a rectangular (83,5 mm

hole centres) flush-mounting box. If necessary, the me-

tallic support for mounting on the wall box can also be

ordered separately using the code EK-SMR.

Note. The screws supplied in the package are su-

itable for standard installations. For more specific

applications, where the screws have to be replaced,

only flat-head screws must be used.

Note. The screws for the metal support must be

tightened with a max. torque of 1.0 Nm.

Mounting of rockers

For the mounting of the rockers on the dedicated seats,

the fixing elements must be aligned vertically.

Switching, display and connection elements

The device is equipped with mechanisms for switching, 2

LEDs for each channel, a programming LED and a pro-

gramming pushbutton and a terminal block for connection

of the bus line.

Switching elements

• Pushbutton (3) for switching between the normal and

programming operating mode

• Mechanisms (4) for independent switching of single or

group of loads (to be completed with square rockers)

Mounting

not allowed

(fixing

elements

aligned

horizontally)