Door Entry Direct 603SK Installation Manual

Browse online or download pdf Installation Manual for Intercom System Door Entry Direct 603SK. Door Entry Direct 603SK 2 pages. Wireless intercom system

Print Page

Ver 3

Installation

1) Before installing fully, test the range of the system. Wire the unit as per

wiring diagram, place the equipment in the desired location and test

operation.

2) Ensure that the gate transmitter / receiver unit is installed to facilitate

line of sight with the property or reception area. To achieve best results,

mount the unit as high as possible from the ground. Should you need to

extend range, you can mount it on a small pole to elevate it a few meters

from the ground.

150m

Typical

Entrance

Pillar

Transmitter / receiver - Keep

Speech

away from ground, as high as

Unit

possible. For best results, do

not install too close to sources

of electrical interference e.g.

gate automation panel

3) It is recommended to charge the handset for 7-8 hours before use.

4) Power up the handset after inserting the batteries.

5) Wire the door station and transmitter / receiver according to the diagram

below..

8 meters max

Screened CAT 5

(keep short for better audio)

Speech Panel Connections

Speaker

Call

Button

Volt free

relay output

Keypad Connections

(SK model)

Installation Manual

603S & SK Wireless Intercom System

House or

reception

area

For longer range

applications, locate the

handset near a window at

front of property.

Note: Wood and glass only

reduce signal strength by

10-20%. Masonry will reduce

signal strength by 20-50%

per wall. Metal can totally

block signals.

Never drill holes in

Intercom

the top of the

enclosure. Cable

Transmitter

entry should be

through the bottom.

603 Range

Foil screening

wrapped

around MIC

wires for best

performance!

MIC

connections

GND

Solid

shield

wire

Code

button

A/C 12-24v

(optional)

12v

N/C

N/O

dc in

Relay output

(4 sec pulse)

Shielded CAT5 cable

Note: Shield only connects at one end

for

Testing

1) Check all connections are correct before switching on the power.

2) Press the call button on the speech panel.

3) The handset should ring.

4) Press the

button to answer the call and check two way speech.

5) Press

to check the door / gate release function works.

Handset & Operation

ADJUST VOLUME

Press

to adjust volume level,

and press MENU to select and save.

CHANGE RING TONE

Press

and the unit will ring under

the currently select tone. Press

and

to cycle through available

ring tones. Press MENU to select

and save.

CHANGE LANGUAGE

Press

and the unit will display the

currently selected language.

1=English. Press

and

cycle. Press MENU to select and

save.

VOICEMAIL

When the door station is pressed, and not answered within 40 seconds,

the visitor can leave a message. Once complete, the handset will display

the

symbol. Up to 16 messages can be saved.

To listen to voicemail, press MENU to play. If there are more than 1

message, press

and

MENU to play.

= Pause / Exit

SET TIME ON DISPLAY

Press MENU for 2 seconds. The hour digits will begin flashing.

Press

to adjust. Press MENU to cycle from hour setting to

minutes and repeat. Press MENU a third time to exit and save changes.

Coding another handset to the System

To add an extra handset to the system, follow the sequence below..

1) Press and HOLD the code button on the door station for 3 seconds,

until the LED's on the bottom of the board start to flash.

2) Press and hold the Code button on the new handset ignoring the first

short tone, until you hear a confirmation tone ("Di-Do-Do"). This may take

up to 10 seconds.

3) Once the door station lights stop flashing, then you can test the

system by pressing the call button on the door station. The new handset

should ring. If not, repeat the process from the top.

Note: For earlier models, the existing master handset lights will

flash after step 1. You will need to press the MENU button on the

existing handset first, before proceeding to step 2 above.

Reception

indicator

12.21

ON/OFF

Charging

base

Power

LED

to select the message required and press

= Continue

= Delete, long

press = delete all.

Battery

Level

Voicemail

Symbol

Vibration

ON/OFF

Code

Button