Door Entry Direct 603SK Kurulum Kılavuzu

İnterkom sistemi Door Entry Direct 603SK için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Door Entry Direct 603SK 2 sayfaları. Wireless intercom system

Ver 3
Installation
1) Before installing fully, test the range of the system. Wire the unit as per
wiring diagram, place the equipment in the desired location and test
operation.
2) Ensure that the gate transmitter / receiver unit is installed to facilitate
line of sight with the property or reception area. To achieve best results,
mount the unit as high as possible from the ground. Should you need to
extend range, you can mount it on a small pole to elevate it a few meters
from the ground.
150m
Typical
Entrance
Pillar
Transmitter / receiver - Keep
Speech
away from ground, as high as
Unit
possible. For best results, do
not install too close to sources
of electrical interference e.g.
gate automation panel
3) It is recommended to charge the handset for 7-8 hours before use.
4) Power up the handset after inserting the batteries.
5) Wire the door station and transmitter / receiver according to the diagram
below..
8 meters max
Screened CAT 5
(keep short for better audio)
Speech Panel Connections
Speaker
Call
Button
Volt free
relay output
Keypad Connections
(SK model)
Installation Manual
603S & SK Wireless Intercom System
House or
reception
area
For longer range
applications, locate the
handset near a window at
front of property.
Note: Wood and glass only
reduce signal strength by
10-20%. Masonry will reduce
signal strength by 20-50%
per wall. Metal can totally
block signals.
Never drill holes in
Intercom
the top of the
enclosure. Cable
Transmitter
entry should be
through the bottom.
603 Range
Foil screening
wrapped
around MIC
wires for best
performance!
+
MIC
-
connections
GND
Solid
shield
wire
Code
button
A/C 12-24v
-
+
(optional)
12v
N/C
C
N/O
dc in
Relay output
(4 sec pulse)
Shielded CAT5 cable
Note: Shield only connects at one end
for
Testing
1) Check all connections are correct before switching on the power.
2) Press the call button on the speech panel.
3) The handset should ring.
4) Press the
button to answer the call and check two way speech.
5) Press
to check the door / gate release function works.
Handset & Operation
ADJUST VOLUME
Press
or
to adjust volume level,
and press MENU to select and save.
CHANGE RING TONE
Press
and the unit will ring under
the currently select tone. Press
and
to cycle through available
ring tones. Press MENU to select
and save.
CHANGE LANGUAGE
Press
and the unit will display the
currently selected language.
1=English. Press
and
cycle. Press MENU to select and
save.
VOICEMAIL
When the door station is pressed, and not answered within 40 seconds,
the visitor can leave a message. Once complete, the handset will display
the
symbol. Up to 16 messages can be saved.
To listen to voicemail, press MENU to play. If there are more than 1
message, press
and
MENU to play.
= Pause / Exit
SET TIME ON DISPLAY
Press MENU for 2 seconds. The hour digits will begin flashing.
Press
or
to adjust. Press MENU to cycle from hour setting to
minutes and repeat. Press MENU a third time to exit and save changes.
Coding another handset to the System
To add an extra handset to the system, follow the sequence below..
1) Press and HOLD the code button on the door station for 3 seconds,
until the LED's on the bottom of the board start to flash.
2) Press and hold the Code button on the new handset ignoring the first
short tone, until you hear a confirmation tone ("Di-Do-Do"). This may take
up to 10 seconds.
3) Once the door station lights stop flashing, then you can test the
system by pressing the call button on the door station. The new handset
should ring. If not, repeat the process from the top.
Note: For earlier models, the existing master handset lights will
flash after step 1. You will need to press the MENU button on the
existing handset first, before proceeding to step 2 above.
Reception
indicator
12.21
ON/OFF
MENU
Charging
base
to
Power
LED
to select the message required and press
= Continue
= Delete, long
press = delete all.
Battery
Level
Voicemail
Symbol
Vibration
ON/OFF
Code
Button