AmerTac Westek LS3101RGB Owner's Manual

Browse online or download pdf Owner's Manual for Light Fixture AmerTac Westek LS3101RGB. AmerTac Westek LS3101RGB 2 pages. Color changing light with motion detection

Print Page

LS3101RGB-N1 OWNER'S MANUAL

Location of Controls

1. Tap On/Dim/Color/Off

2. Toggle Switch/Tap Selector

3. Mode Selection Switch in waterproof casing

4. PIR Sensor

5. 3x AA battery door

Indoor/Outdoor Use

This is light is rated IP44 Water Resistant. It is designed to be used indoors or outdoors

under normal operating conditions. It is NOT designed to be submerged in water or

any other liquid. Do NOT expose the light to excessive heat above 105°F (40°C) or

cold below 30°F (-1°C).

To Install Batteries

Use a #1 or #2 Philips Screwdriver (not included) and remove the battery door (5).

Insert 3x new AA in the chamber noting the direction/polarity of each battery.

Place door back on and tighten screw.

Only use fresh batteries. Do not mix old and new batteries.

When lights become dim or sensor no longer operates properly, it is time to install

new batteries.

Please recycle/dispose of the used batteries in the correct manner according to

your local ordinances.

Operate the Light Two Different Ways

There are two modes of operation to choose from. Tap Mode will allow the user

to select White OR Color (Red, Green and Blue) Light. Motion Activated Mode will

only operate in White Color.

2 Modes of Control

Motion Activated

(White Light Only)

Tap Top to Cycle

Through Colors

(White, Red, Green, Blue)

To Choose Mode

There is a Mode Selection Switch (3) located on the bottom of the unit. The switch

is encased in a water-resistant sleeve to protect the unit from malfunction when

operated outdoors. To operate the light in tap mode with color, move the switch to

the RIGHT (ICON). To operate the light as Motion Activated, move the switch to the

LEFT (ICON).

In Motion Activated Mode

This light is equipped with a PIR (passive infrared) sensor (4) that can detect motion

under dusk to dawn conditions up to 10 feet (3m). When Motion Activated Mode is

chosen, BRIGHT WHITE light will activate when the sensor detects movement within

10 feet (3m). Light will remain on until no motion is detected and then shut off 30

seconds after the last recognized movement. Motion detection will not function

properly if the sensor is blocked or tampered with.

In Tap Mode

Tapping the top of the unit lightly (1) will activate a toggle switch/tap selector

on the bottom (2) and change the color of the light. The tap selector is meant

to react to minimal pressure. Pushing heavily or banging on the top of the light is

Under normal use and conditions, AmerTac provides to the original purchaser of this product a one

year limited express warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/

warranties. The Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the

exceptions explained fully in the Limited Warranty on the website.

Mode Switc h

Toggle Switch

COLOR CHANGING LIGHT

WITH MOTION DETECTION

not necessary and will eventually damage the unit. The tap selector must be in

contact with the surface in order to work. The tap selector will NOT work on an

uneven surface (such as wicker, sand or dirt). You can manually click the toggle

to change the light color if you are using the light on a surface where the tap

function does not operate.

To select the color of the light:

Tap for BRIGHT WHITE

Tap for DIM WHITE

Tap for RED

Tap for GREEN

Tap for BLUE

Tap OFF

Battery Precautions:

1. Use only the size and type of batteries specifi ed.

2. Always purchase the correct size and grade of battery most suitable for the

intended use.

3. Be sure to follow the correct polarity when installing the batteries as indicated in

the battery compartment.

Reversed batteries may cause damage to the device.

4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium)

batteries.

5. Replace all batteries of a set at the same time. Do not mix old and new

batteries.

6. Clean the battery contacts and also those of the device prior to battery

installation.

7. Do not dispose of batteries in fi re.

8. Remove batteries if consumed or if product is to be left unused for an extended

period of time.

FCC Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Modifi cations to this product not approved by the party responsible for

compliance could void the user's authority to operate the product.

250 Boulder Dr.

Breinigsville, PA 18031

610-336-1330

www.amertac.com

Made in China / Fabriqué en

Chine / Fabricado en China

I18-0062-A