Douglas Lighting Controls WRS-2224 Instruction Manual - Page 11

Browse online or download pdf Instruction Manual for Scanner Douglas Lighting Controls WRS-2224. Douglas Lighting Controls WRS-2224 20 pages. Programmable relay scanner

Print Page

Setup: Time Out Option

TIME OUT OPTION

A l l o w s o n e r e l a y g r o u p t o h a v e t h e T I M E O U T f e a t u r e .

IMPORTANT : I f t h e r e l a y g r o u p o f a n i n p u t h a s t h e T I M E O U T

f e a t u r e a s s i g n e d , t h e i n p u t w i l l not sw i t c h t h e r e l a y g r o u p .

I n s t e a d , t h e i n p u t w i l l e n a b l e t h e T I M E O U T f e a t u r e w h e n

t u r n e d O N a n d d i s a b l e t h e T I M E O U T f e a t u r e w h e n t u r n e d o f f .

TIME OUT during Closed Hours

Mode

Change

TIME OUT mode

enabled at start of

closed hours

To Assign the Time Out Option:

1. Make sure the output relays are properly connected to the output

terminals and that the timer output is properly connected to the

selected input terminal.

2. Make sure NORMAL MODE is selected. Its top indicator LED should be ON.

3. Use the INPUT SELECT button to select the designated group #1-5

(when its indicator INPUT LED is ON).

4. Press the PROGRAM MODE select button. Its indicator LED will begin

flashing. If you have not already done so, select the output relays that

belong to that input.

5. Press the OPTIONS MODE button until the TIME OUT indicator LED

turns ON. (Pressing the OPTIONS MODE button will cycle the

selections from FLICK WARN to TIME OUT to TIME OUT with FLICK

WARN back to NO SELECTION.)

6. If you want to assign the TIME OUT option with a FLICK WARN to the

group, press the OPTIONS MODE button until both the TIME OUT and

the FLICK WARN indicator LEDs are ON.

7. Return to NORMAL mode.

8. For the group assigned the TIME OUT option, the TIME OUT indicator

LED will be ON whenever the group is selected, and the FLICK/TIME

OUT ACTIVE LED will flash whenever the TIME OUT operation is

occuring.

NOTE:

Only one group can be assigned the TIME OUT option. If

more than one group is assigned TIME OUT, those groups

will not respond to input or override switch commands.

It will be necessary, in that case, to shut off and restart the

Relay Scanner, and then re-program all of the input groups

with only one all-inclusive group assigned TIME OUT.

WRS-2224: Directions & Applications

Exit without

Light turned ON

with wall switch:

switching OFF

timer starts

W h e n a c t i v e , T I M E O U T c a u s e s t h e r e l a y o u t p u t t o s t a r t a n i n t e r n a l

t i m e r w h e n e v e r t h e c o n n e c t e d r e l a y i s s w i t c h e d O N . U p o n t i m e

e x p i r y ( 2 h o u r s l a t e r ) t h e o u t p u t s w i t c h e s t h e r e l a y O F F .

T I M E O U T i s t y p i c a l l y e n a b l e d a n d d i s a b l e d w i t h a t i m e c l o c k

c o n n e c t e d t o t h e i n p u t . A s a c o m m o n e x a m p l e , u s e t h e t i m e

c l o c k t o e n a b l e T I M E O U T d u r i n g c l o s e d h o u r s . T h u s , l o c a l

s w i t c h e s w i l l w o r k n o r m a l l y d u r i n g b u s i n e s s h o u r s a n d f u n c t i o n

w i t h T I M E O U T d u r i n g c l o s e d h o u r s .

Timer expires,

lights switched OFF

To De-Assign the Time Out Option:

1. Select the group (with INPUT SELECT).

2. Go to PROGRAM mode.

3. Press the OPTIONS button so that both the TIME OUT and the

FLICK WARN indicator LEDs are OFF

4. Return to NORMAL mode.

Flick Warn

LED

Output Mode

Select Button

Program Mode

Select Button

page 9

OFF

TIME OUT mode

Switches work normally

disabled at start of

(no TIME OUT) during

business hours

Time Out

LED

Normal Mode

Select Button

Flick/Time Out

Active LED

Scanner Input

When set in TIME OUT mode,

the time clock enables TIME OUT

with an ON signal and disables

TIME OUT with an OFF signal.

Relays that are assigned to the

group are not switched.

Input

Select

LEDs

Button

DOUGLAS

lighting controls

WTP-4408

Time Clock

Esc

Clr

S e n s o r