Bosch ASCENTA SHX6AP Use And Care Manual - Page 11

Browse online or download pdf Use And Care Manual for Dishwasher Bosch ASCENTA SHX6AP. Bosch ASCENTA SHX6AP 21 pages. Bosch ascenta models dishwashers use & care manual
Also for Bosch ASCENTA SHX6AP: Use And Care Manual (21 pages), Use & Care Manual (26 pages)

Print Page

Bosch ASCENTA SHX6AP Use And Care Manual

OPERATING

THE SHX3AM,

SHX5AL,

& SHX6AP

I @BOSCH

oo<_®

off

o o o

.................

Power

RegWar

Quick

tgLJ

Scrub

Wash

0 Clear 0 RbseAgent

Program

Select

i @

3he

BOSCH

_"®

9 h •

Delay

Half load

WARNING

//_:,\

® Active

@ Sanitized

_ Start/

}_!

Power

Auto

Regular

Delicate

Quick

Scrub

Wash

\ ......

Clean

RinseAgent

Preg[am Select

You could

be seriously

scalded

if you allow

hot water

to splash

out of the dishwasher.

OPEN THE DOOR CAREFULLY

during

any

wash

or rinse cycle. Do not fully

open the door until

water

noises

have stopped.

To Start

Unit:

• Door must be open. Press the "ON/OFF" button to turn the unit on.

• One of the Wash Cycle Indicator

Lights will be flashing

to show

you are in the Wash Cycle selection

mode.

• Press the "<" or ">" button

to select the desired wash cycle.

•

Press the "START" button

(Wash

Cycle Indicator

Light will stop

flashing)

• Close the door to start

the cycle

Note:

Rinse Agent

Indicator

Light

will

be illuminated

if the unit

needs Rinse Agent.

Note: If you close the door without

pressing

the start

button

the

unit will beep.

To Cancel

the

Cycle:

• Open the door just far enough

to expose the controls,

Be careful

of water

Splash Out!

• Press and hold the"START/RESET"

button

until the "Active"

indica-

tor Light goes out,

•

Close the door and wait for about

1 minute

for the dishwasher

to drain.

• Open the door and press the "ON/OFF"

button.

• You are now ready to start a new cycle.

Setting

Options

(Rinse

Agent

Amount

/ Extra

Dry

Heat

Activation

/ Cycle

Completion

Signal

Tone

Level)

•

Door must

be open.

Press the "ON/OFF"

button

to turn

the unit

on.

• One of the Wash Cycle Indicator

Lights will be flashing

to show

you are in the Wash Cycle selection

mode.

• To enter the Options

Setup Mode,

press and hold down the ">"

button,

then

press and release the "START RESET" button,

then

release the ">" button.

• The"Clean"

Indicator

Light and at least one addition

Indicator

Light

will be flashing

to show you are in the Options

Setup Mode.

•

Press the ">" button

to select

the option

you would

like to ad-

just.

o If the "CLEAN" and "RINSE AGENT" Indicator

Lights are flashing

you are ready to set the amount

of Rinse Agent

the unit will

dispense.

o If the "CLEAN" and "SANITIZED"

Indicator

Lights are flashing

you

are ready to turn your Extra Dry Heat option

on/off.

o If the "CLEAN" and "SANITIZED"

and "RINSE AGENT" Indicator

Lights are flashing

you are ready to set the Cycle Completion

Signal Tone Level.

To Set the Amount

of Rinse Agent

Dispensed

NOTE: If your glasses have spots you need more Rinse Agent. If your

glasses have streaks you need less Rinse Agent.

• With the "CLEAN" and "RINSEAGENT" Indicator Lights flashing.

• Press the "<" button to change the amount of Rinse Agent Dis-

pensed.

• As you press the "<" button you will notice the Wash Cycle Indica-

tor Lights illuminating.

•

If none of the Wash Cycle Indicator Lights are illuminated,

the Rinse Agent Dispenser is turned off.

• If one of the Wash Cycle Indicator Lights are illuminated, the

Rinse Agent Dispenser is set to deliver the lowest charge of Rinse

Agent.

•

If two of the Wash Cycle Indicator Lights are illuminated, the

Rinse Agent Dispenser is set to deliver a medium charge of Rinse

Agent.

• Ifthree ofthe WashCycleIndicator Lights areilluminated, the Rinse

Agent Dispenser is set to deliver the largest charge of Rinse Agent.

• Press "START"to save your settings.

To Turn the Extra Dry Heat On or Off

• With the "CLEAN" and "SANTITIZED" Indicator Lights flashing.

• Press the "<" button to change the Extra Dry Heat setting.

• As you press the "<" button you will notice the Wash Cycle Indica-

tor Lights illuminating.

o If none of the Wash Cycle Indicator Lights are illuminated,

the

Extra Dry Heat option is turned off.

o If one of the Wash Cycle Indicator Lights are illuminated,

the

Extra Dry Heat is turned on.

• Press"START"to save your settings.

To Set the Cycle Completion

Signal

Tone Level

• With the "CLEAN" and "SANITIZED" and "RINSEAGENT" Indicator

Lights flashing.

• Press the "<" button to change the Cycle Completion Signal Tone

Level.

• As you press the "<" button you will notice the Wash Cycle Indi-

cator Lights illuminating

and the Cycle Completion Signal Tone

level changing.

o If none of the Wash Cycle Indicator Lights are illuminated,

there

will be no tone. The Cycle Completion Signal is turned off.

o If one of the Wash Cycle Indicator Lights are illuminated,

there

will be a low Cycle Completion Signal Tone Level.

o If two of the Wash Cycle Indicator Lights are illuminated,

there

will be a medium Cycle Completion Signal Tone Level.

o If three of the Wash Cycle Indicator Lights are illuminated,

you

will be at the maximum Cycle Completion Signal Tone Level.

• Press"START"to save your settings.