Targa by Draper
Wiring Diagrams—Plug & Play 110-120V Motor
(Low Voltage Control Built Into Motor)
Single Low Voltage Control
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Data
Cable
Wall Switch,
RF or IR
Receiver,
110-120V
or integrated
Plug
control system
Wiring Diagrams (Standard and Quiet Motors)
Please Note: Do not wire motors in parallel.
Single Station Control
Internal Screen Wiring
White (Common)
Black (Directional)*
Red (Directional)*
Green/Yellow (Ground)
Dashed wiring
by electrician
Control
Single gang box by others
switch
Min. 4" x 2
/
" x 1
/
" deep
1
7
8
8
Blue
Red
Black
Location of key
operated on-off
switch if furnished
To 110-120V Line
*Motor Direction
Motor Type
Up
Down
Standard
Red
Black
Quiet
Red
Black
INTERNAL SCREEN WIRING
White (Common)
Red (Up)
Black (Down)
Green/Yellow
(Motor Ground)
To
110-120 VAC
L1
Line
N
GND
*Motor Direction
Motor Type
Up
Standard
Red
Quiet
Red
Multiple Low Voltage Controls
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Data
Cables
Wall Switches,
RF or IR
Receivers,
110-120V
or integrated
Plug
control systems
Multiple Station Control
Internal Screen Wiring
White (Common)
Black (Directional)*
Red (Directional)*
Green/Yellow (Ground)
Cap off with wire
nut and tape
Red
Blue
Dashed wiring
Black
by electrician
Red
Blue
Black
Red
Blue
Single gang box by others
Black
/
" x 1
/
" deep.
Min. 4" x 2
1
7
8
8
3 shown. More or less equally
feasible.
Location of key
operated on-off
switch if furnished
To 110-120V Line
External LVC-IV - Single or Multiple
Projection Screen Wiring Diagram
Wiring Diagram – External LVC-IV
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110V-220V AC-Hot
Black-to 110V-220V AC-Hot
White -Common to screen & 110V-220V AC Neutral
Green/Yellow (Ground)
Location of key
operated on-off
switch if furnished.
Dashed wiring by electrician
Low voltage wiring by others
Down
Black
Black
www.draperinc.com
Wiring Diagrams—110-120V Motor
(Low Voltage Control Built Into Motor)
Single Low Voltage Control
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Data
Cable
Wall Switch,
RF or IR
Receiver,
or integrated
control system
To 110-120V Line
Built-in Low Voltage Motor: Switch-to-Motor—
Dry Contacts or Data Cable connection
INSERT MOTOR DATA
Back of
CABLE HERE
wall switch.
Please Note: 5V DC must be
connected to be able to set
limits using the wall switch.
Receiver
Button
(765) 987-7999
Page 4 of 4
Multiple Low Voltage Controls
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Wall Switches,
RF or IR
Receivers,
or integrated
control systems
To 110-120V Line
Please Note:
Although both Dry
Contact and Data
Cable connections
are shown, you
should only use
one connection
type per motor.
Please Note:
This Splitter/Jack
is located inside the
motor-end endcap
of your screen.
To access, remove
access panel from
endcap.
Data Cables to switches
or to additional motorscan
be plugged into any of the
three open jacks.
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Electrically Straight
Data Cable to more
LVC-IV modules*
RS232/485
Inputs/Outputs
Wall Switch
IR Eye Input
*A maximum of six (6)
Low Voltage
LVC-IV modules can
Trigger
be linked together.
3-28 VDC
Data
Cables
Print Page