Targa and Premier—Large Sizes by Draper
Wiring Diagrams (Standard and Quiet Motors)
Please Note: Do not wire motors in parallel.
Single Station Control
Internal Screen Wiring
White (Common)
Black (Directional)*
Red (Directional)*
Green/Yellow (Ground)
Dashed wiring
by electrician
Control
Single gang box by others
switch
Min. 4" x 2
1
/
" x 1
8
Blue
Red
Black
Location of key
operated on-off
switch if furnished
To 110-120V Line
*Motor Direction
Motor Type
Up
Down
Standard
Black
Red
Quiet
Red
Black
Internal Screen Wiring
White (Common)
Red (Up)
Black (Down)
Green/Yellow
(Motor Ground)
N
To
110-120 VAC
L1
Line
GND
*Motor Direction
Motor Type
Up
Down
Standard
Black
Red
Quiet
Red
Black
Built-in Low Voltage Motor: Switch-to-Motor—
Dry Contacts or Data Cable connection
Please Note: 5V DC must be
connected to be able to set
limits using the wall switch.
INSERT MOTOR DATA
CABLE HERE
Back
of wall
switch.
Data Cables to switches or to additional motors
can be plugged into any of the three open jacks.
Multiple Station Control
Internal Screen Wiring
White (Common)
Black (Directional)*
Red (Directional)*
Green/Yellow (Ground)
Cap off with wire
nut and tape
Red
Blue
7
/
" deep
8
Black
Red
Blue
Black
Red
Blue
Single gang box by others
Black
Min. 4" x 2
3 shown. More or less equally
feasible.
Location of key
operated on-off
switch if furnished
To 110-120V Line
Wiring Diagram – External LVC-IV
White-Common to screen & 110 VAC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110 VAC-Hot
Black-to 110 VAC-Hot
Green/Yellow (Ground)
Location of key
operated 0n-off
switch if furnished.
Dashed wiring by electrician
Low voltage wiring by others
Please Note:
Although both Dry
Contact and Data
Cable connections
are shown, you
should only use
one connection
type per motor.
Please Note: This
Splitter/Jack is
located inside the
motor-end endcap
of your screen. To
access, remove
access panel from
endcap.
www.draperinc.com
Wiring Diagrams—Plug & Play 110-120V Motor
Single Low Voltage Control
Dashed wiring
by electrician
110-120V
Plug
1
/
" x 1
7
/
" deep.
8
8
Receiver
Button
Wiring Diagrams—110-120V Motor and Quiet Motor
with Built-in Low Voltage Controller (LVC-IV)
Single Low Voltage Control
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Dashed wiring
by electrician
Wall Switch,
RF or IR
Receiver,
or integrated
control system
To 110-120V Line
(765) 987-7999
(Low Voltage Control Built Into Motor)
Multiple Low Voltage Controls
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Data
Cable
Wall Switch,
RF or IR
Receiver,
110-120V
or integrated
Plug
control system
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Electrically Straight
Data Cable to more
LVC-IV modules*
RS232/485 Inputs/Outputs
Low Voltage Trigger
3-28 VAC
*A maximum of six (6)
IR Eye Input
LVC-IV modules can be
linked together.
Multiple Low Voltage Controls
Dashed wiring
by electrician
Data
Cable
Wall Switch(es),
or integrated
control systems
To 110-120V Line
Page 4 of 4
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Data
Cables
Wall Switches,
RF or IR
Receivers,
or integrated
control systems
Wall Switch
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Data
Cable(s)
RF or IR
Receivers,
Print Page