Draper FlexShade NEXD Installation & Operation Instructions - Page 5
Browse online or download pdf Installation & Operation Instructions for Indoor Furnishing Draper FlexShade NEXD. Draper FlexShade NEXD 6 pages. Clutch-operated small and large hardware
Also for Draper FlexShade NEXD: Instructions Installation & Operation (8 pages), Instructions Manual (8 pages), Instructions Installation & Operation (8 pages), Instructions Installation & Operation (10 pages), Instructions Manual (12 pages)
Print Page
Clutch Operated FlexShade
Window shade with heavy duty clutch and 3" hardware profile. Cassette option.
Section 5 - Shade Fabric Roller Mounting
(clutch)
1. Carefully work open
end of roller onto bead chain
(Fig.
5-A).
clutch
2. Slide idler end pin up through
one of the slots on
idler endcap,
(Fig. 5-B)
and
into seat for pin.
3. Ensure that all mounting hardware
is secure and fully tightened.
4. Test shade to ensure that roller
is level and operating properly. If
not, adjust idler leveling screw with
provided hex wrench
(Fig.
5-C).
Caution: Do not allow shade roller to become exposed by running shade fabric too far down. Be sure to use stop balls provided in hardware packet by
Draper to set up and down travel limits. Stop balls by others may be too small, and become lodged in clutch mechanism.
Please Note: If shade fabric is uneven, see "Field Adjustments" on page 4.
Section 6 - Bead Chain Limits and Safety Device Installation
Section 6.1 - Attaching Stop Balls
1. Set upper and lower travel limits by installing stop balls to bead chain
Section 6.2 - P-Clip Cord Tension Device
Please Note: Draper Bead Chain Clutch Operated shades that do not comply with WMCA/ANSI Standard A100.1-2012 come with
a cord tension device pre- attached to bead chain
bead chain is held taut enough that children cannot pull it away from wall or fit their head into loop.
Section 6.3 - Spring-Loaded Cord Tension Device
If Draper Clutch FlexShade complies with WMCA/ANSI Standard A100.1-2018, a Spring-Loaded
Cord Tension Device comes installed on bead chain
label and approved mechanical fasteners
children cannot pull bead chain away from wall or fit their head into loop.
page
2). For more information, visit
1. Install cord tension device to wall, jamb or sill.
2. Pull tensioner down so that bead chain is held taut and use mounting hardware to keep it taut.
Please Note: Bead chain should be taut enough to move smoothly through device. However,
overtightening screws will damage Spring Loaded Tension Device.
Section 7 - Fascia
1. Place groove along top of fascia over endcaps.
2. Snap into place
(Fig.
9).
Please Note: Fascia is not fully seated until it clicks into place on both ends. Once in place,
check for secure fit.
Figure 5-A
Open (clutch)
End of Roller
Assembly
(Fig.
(Fig.
8). An approved permanent warning
(wood screws)
are included. Device is designed so that
www.draperinc.com/WindowShades/WCMAcompliance.asp.
NEXD
®
Idler Pin Paths
(crimp closed using pliers) (Fig.
x). This device must be attached to wall, jamb or sill so that
(See safety note on
Figure 5-B
Figure 5-C
Adjust Idler
d
E n
e r
Leveling Screw
I d l
r
l l e
with the
R o
b l y
o f
s e m
provided
A s
Hex Wrench
Figure 6
6).
Figure 8
Sill
Mount
Tensioner
Insert
Fascia
STEP 1
Figure 9
page 5 of 6
d
E n
e r
I d l
r
l l e
R o
b l y
o f
s e m
A s
Attach
Stop Balls
Crimp
Closed
with
Pliers
Figure 7
Jamb
Mount
STEP 2
Clicks
into place