Electrolux RH30WC40GS Installation, Use & Care Manual - Page 10
Browse online or download pdf Installation, Use & Care Manual for Ventilation Hood Electrolux RH30WC40GS. Electrolux RH30WC40GS 19 pages. Universal/multiflex
Also for Electrolux RH30WC40GS: Brochure & Specs (2 pages), Factory Parts Catalog (4 pages)
Print Page
Installing the hood
10
10
10
10
10
Step 6
Step 6
Step 6
Step 6
Step 6
For r
For r
ectangular ducted discharge installations only
ectangular ducted discharge installations only
For r
For rectangular ducted discharge installations only
For r
ectangular ducted discharge installations only
ectangular ducted discharge installations only
(otherwise skip to next step)
Attach exhaust adaptor/damper over knockout
Attach exhaust adaptor/damper
Attach exhaust adaptor/damper
Attach exhaust adaptor/damper
Attach exhaust adaptor/damper
opening with two exhaust adaptor screws. Make
sure
damper pivot
pivot
pivot is nearest to top/back edge
pivot
pivot
Remove tape
tape
tape
tape from damper flap.
tape
Pivot
NOTE: The exhaust adaptor/damper can be installed
NOTE:
NOTE:
NOTE:
NOTE:
up to 1 inch on either side of the hood center to
accommodate off-center ductwork. In extreme off-
center installations, one end of the duct connector
may need to be trimmed to clear the electrical cable
clamp.
Step 7
Step 7
Step 7
Step 7
Step 7
For round ducted discharge installations only
For r
For r
ound ducted discharge installations only
ound ducted discharge installations only
ound ducted discharge installations only
For r
For r
ound ducted discharge installations only
Re-install the r r r r r ound transition
7" Round
Transition
NOTE:
NOTE:
NOTE:
NOTE:
NOTE: The round transition can be installed up to 1
inch on either side of the hood center to
accommodate off-center ductwork. In extreme off-
center installations, one end of the duct connector
may need to be trimmed to clear the electrical cable
clamp.
top/back edge of hood.
top/back edge
top/back edge
top/back edge
Top/back
edge
Exhaust
transition/damper
ound transition
ound transition
ound transition with its screws.
ound transition
Step 8
Step 8
Step 8
Step 8
Step 8
Mark holes
Mark holes
Mark holes
Mark holes
Mark holes
Select the vent option that your installation will
require and proceed to that section:
Outside top exhaust
Outside top exhaust
Outside top exhaust
Outside top exhaust
Outside top exhaust
(Vertical duct– 3 1/4"x 10" Rectangular)
Use the diagram or the hood as a template and mark
the locations on the cabinet for ductwork, electrical
wiring and keyhole screw slots.
Hood mounting screws (4)
13 15/16" (30" Hood)
13 15/16" (30" Hood)
16 15/16" (36" Hood)
16 15/16" (36" Hood)
Cabinet front
12 9/16"
Cabinet Bottom
5 1/4"
5 1/4"
Vertical duct
"
5"
access hole
"
1 1/4"
Center
Wood shims (recessed
line
bottom cabinets only)
Outside top exhaust
Outside top exhaust
Outside top exhaust
Outside top exhaust
Outside top exhaust
(Vertical duct–7" Round)
Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Hood mounting screws (4)
13 15/16" (30" Hood)
13 15/16" (30" Hood)
16 15/16" (36" Hood)
16 15/16" (36" Hood)
Cabinet front
Cabinet Bottom
Access
8" DIA.
hole for 7"
HOLE
round duct
Center
Wood shims (recessed
line
bottom cabinets only)
"
10 1/2"
2"
1 1/4"
Electrical access hole
Electrical access hole
(in cabinet bottom)
(in cabinet bottom)
"
12 1/2"
10 1/2"
2 1/4"
5"
1 1/2"
Electrical access hole
Electrical access hole
(in cabinet bottom)
(in cabinet bottom)