DSC PC51O2-433NA Installation Manual - Page 3

Browse online or download pdf Installation Manual for Security System DSC PC51O2-433NA. DSC PC51O2-433NA 13 pages.

Print Page

2.5 Connecting a Garage Door to the PC5102-433

ANT1

NO1

NC1

COM1

NO2

NC2

COM2

Garage door

pushbutton

or motor

an output on the PC5102-433 will follow a main panel output that is programmed as a

command output and is set up on the wireless key as such. Doing this will also activate an

output on the PC5102-433 for 5 seconds (please refer to the control panel manual for a listing

of available output types and their functions). PGM 1 and/or PGM 2 on the PC5102-433 can

be set up to open a garage door (please refer to Section 4.1).

2.6 Connecting an X-10 Powerflash Module to the PC5102-433

When connecting an X-10 Powerflash module to the PC5102-433, different lights within or

outside the home can be controlled, such as table lamps, or porch and driveway lights that

illuminate the entry / exit paths.

This can be done by setting up the system and

wireless key in one of several ways:

• The wireless key can toggle an output ON/

OFF, triggering the X-10 Powerflash

module, providing direct control of

lighting.

• The wireless key can turn on an output for

a programmable amount of time (5

seconds to 99 minutes and 99 seconds),

turning on lights for the amount of time the

homeowner requires.

• The PC5102 output can be programmed to follow a main panel output which can turn

on lights when the panel is armed and turn them off when disarmed, turn on lights

when an alarm occurs and turn them off when disarmed, etc. Please refer to the

control panel Installation Manual for a listing of available output types and their

function. PGM 1 and/or PGM 2 on the PC5102-433 can be set up for this operation

(see Section 4.1).

Section 3: Enrolling Wireless Keys

This section describes how to enroll wireless keys. For more information on these keys, read the

instruction sheet included with each key.

3.1

A Note about Electronic Serial Numbers

An electronic serial number (ESN) is printed on the back of each wireless key. ESNs are used

to enroll the wireless keys with the PC5102-433 receiver.

In order to reduce the occurrence of wireless keys with the same serial number, 6-digit serial

numbers are now printed on the back of each wireless key. The 6-digit serial numbers include

hexadecimal digits. For instructions on programming hexadecimal numbers, see your system

Installation Manual , Section 4: How to Program.

NOTE

NOTE: 6-digit serial numbers are only supported on the following control panels: PC5020, P-

NOTE

8+, PC501X v2.0 & higher, P832/DL v2.0 and higher, PC1555(MX), P-6B(MX), PC580 and P-48.

The (P)WLS909-433 and (P)WLS919-433 keys have both a 5-digit and a 6-digit serial number

printed on them. When connecting the PC5102-433 to a PC5010 v1.x or P-832 v1.x panel, enter

5-digit serial numbers only. When connecting the PC5102-433 to a PC5020, P-8+, PC5015 v2.x

and higher, P832DL v2.x and higher, PC5010 v2.0 and higher, P832 v2.0 and higher,

PC1555(MX), P-6B(MX), PC580 or P-48 panel enter the 6-digit serial number.

Connect an output of the PC5102-433 across the

wall-mounted push button or directly at the motor

RED

BLK

YEL

GRN

of the garage door opener (please consult the

garage door opener instructions for proper con-

nections). Set up the system and wireless key so

that it is programmed to pulse an output for a short

duration (5 seconds) so that every time the pro-

grammed key is pressed the garage door is opened

or closed. The system can also be set up so that

firealarmresources.com

ANT1

COM1

NO2

NO1

NC1

Lamp

Module

X-10

Powerflash

Module

NC2

COM2

RED

BLK

YEL

GRN