DSE DK-WP4-DVR User Manual - Page 2
Browse online or download pdf User Manual for Security Camera DSE DK-WP4-DVR. DSE DK-WP4-DVR 2 pages. Camera and video recorder in wall clock
Print Page
USER'S MANUAL
each time the front PIR sensor is detected. When no
human presence is detected in the room, the camera goes
into stand-by and waits for a new intrusion.
Movie playback on PC
A computer and SD card reader (included) is required to
review and manage the files recorded by the DVR.
You need to turn off the DVR with the ON / OFF switch.
remove the micro SD card and insert it into a computer
SD card reader.
It is possible to copy the videos to the PC and play them
with any video player (VLC - VideoLan recommended).
ATTENTION: It is not possible to download the files
through the USB cable of the DVR because this is used
only for recharging / powering the device.
Date and time setting and options
To set the system date and time and to configure the
operating options, a text file called TIME.TXT is used,
which you will find in the root directory of the SD card
after making recordings. If you open it with notepad you
will see this content:
Resolution = 0; (0 = 1080P, 1 = 720P; 2 = 480P)
Audio_Record = 1; (0 = Off, 1 = On)
Loop_Record = 1; (0 = Off, 1 = On)
Record_Time = 1; (0 = 1min, 1 = 3min, 2 = 5min, 3 =
10min)
Motion_Level = 0; (0 = highest, 1 = high, 2 = middle, 3 =
low, 4 = lowest)
Motion_Time = 1; (0 = 1min, 1 = 3min, 2 = 5min, 3 =
10min)
Date_Stamp = 1; (0 = Off, 1 = On)
Time_set = N2020 / 01/01 00:00:00; (Y = change N = No
change)
Each option has its factory choice alongside, for example
the resolution is equal to 0, which means 1080P
You can change each option by following the directions on
the side
RESOLUTION - Sets the resolution of the recording,
factory default 0 = 1080P
AUDIO RECORD - Sets whether to record audio, factory
default 1 = audio active
LOOP RECORD - Sets the automatic overwriting when the
memory is full, factory 1 = active
RECORD TIME - Sets the duration of the video in
continuous recording, factory 1 = 3 minutes
MOTION LEVEL - Sets the sensitivity of the motion
detection, factory default 0 = maximum
MOTION TIME - Sets the duration of motion recording
videos, factory default 1 = 3 minutes
DATE STAMP - Enables the overlay of date and time, by
default 1 = enabled
TIME SET - Set date and time as in the following example
Time_set = Y2020 / 09/26 19:15:00; (Y = change N = No
change)
The appliance will accept the new settings at the next
start. Be careful not to change the punctuation and spaces
in the file or the settings will be invalid. Note that the time
DK-WP4-DVR Camera with clock video recorder
DSE srl - Digital Surveillance Equipment - www.dse.eu
Document: DK-WP4-DVR2I0
setting is only valid for a switch on as the appliance is not
able to keep it from switched off.
Main technical characteristics
Sensor
Maximum resolution
Frame rate
Video format
Overlay
Functions
Audio microphone
Video storage
Operating
temperature
Internal battery
Memory
Memory capacity
Page: 2
CMOS
FullHD 1080p (1920x1080)
30 f / sec
MOV (H264 compression)
Date time (excludable)
Recording on PIR detection
Incorporated
About 19 hours on 128GB at
1080P
-5 ° + 40 ° C
3Ah 4 months in stand-by
MicroSD Class 10 or higher
4..128 GB