AnyBeam HD301M1-H2 User Manual - Page 2
Browse online or download pdf User Manual for Projector AnyBeam HD301M1-H2. AnyBeam HD301M1-H2 3 pages. Mems laser scanning projector
Print Page
Troubleshooting 1
No images are projected
Problem
Loose Micro USB Cable or no
Connection
(LED Indicator 1: OFF)
Internal Protected Mode is activated due
to unknown factors
(LED Indicator 1: blink rapidly)
Standby and Power Saving Mode
(LED Indicator 1: OFF
LED Indicator 2: flashes every 3 seconds)
Troubleshooting 2
The image is not projected properly
(NO SIGNAL sign shown only)
Problem
Loose HDMI Cable (AV I/O)
(LED Indicator 1: remains on
LED Indicator 2: OFF)
No Signal output from the video sources
(LED Indicator 1: remains on
LED Indicator 2: OFF)
Troubleshooting 3
Image Display Error
Problem
The color does not look appropriate
( e.g. color bias too red, yellow or green
etc.)
Image jitter ( MEMS work abnormal
due to unknown factors)
The image is flickering or blurred
Unexpected frame color (green, red or
blue etc.) shown in the Margin of left/
right side of the display or word
Partial area blurred or color fringing
appeared in the display
Image distortion appeared and could not
project correctly
Other abnormal Status of projected
image
Troubleshooting 4
Built-in Speaker / Audio Problems
Problem
There is no Sound
Silent Mode is selected
Other abnormal Status of Sound
Troubleshooting 5
Connected Speaker / Audio Problems
Problem
Specific speakers may not output audio
properly
Support：
•
User Manual
Product Instruction and Troubleshooting are included.
•
Technical Support
If there is any question, please refer to the user's manual first. If the issue still exits after
conducting default settings, please inquire and contact the service center for help from
below link.
Official Website: www. Anybeamstore.com
Email:
Tel: +886-(0)2-2918-1991
Warranty：
•
Limited Warranty Period: 1 year
AnyBeam warrants its Product(s) under normal use during the warranty period. (Self- assembly/
disassembly/ missuses are not included)
•
For return your item, if the device is damaged, worn, scratched, stained or so due to mistaken usage
of assembly/ disassembly, you will be responsible for paying for your own shipping costs and
maintenance charges for returning your item.
Inspection/ Solution
Check whether the cable is connected correctly to the power
adaptor (DC 5V/ 1.5A or greater output).
Unplug and plug the cable to restart the device. If same case
happened, please replace other power adapter (DC 5V/ 1.5A
or greater output), then connect it again.
The projector enters standby status at the specified time, when
no signal output from the video source device. Please awake
the projector by resuming signal or press the jog lever.
Inspection/ Solution
Check whether the HDMI cable is connected correctly or
loose in both input/ output terminal.
Check whether the video source (Output) is sending the
content to the projected device (Input) correctly.
1. Check whether the native projected image is output
abnormal.
2. Unplug and plug again the cable from the device to restart.
1. Unplug and plug again the cable from the device to restart.
2. Replace other power adapter (DC 5V/ 1.5A or greater
output), and reconnect the device to restart.
3. Remove any metal or magnetic material from the device,
then unplug and plug it again to restart.
4. Check whether there's any source of vibration (e.g.
speaker, vibration will cause abnormal function of
MEMS).
Hold down the jog lever for 3 seconds to enter the OSD
mode. Select [Sharpness] to adjust.
Hold down the jog lever for 3 seconds to enter the OSD
mode. Select [Green/ Blue Alignment] to adjust.
Make sure the lens is clean with no dust and check again.
AnyBeam suggests 720p resolution input. Some other
resolution may not be projected
Unplug and plug again the cable from the device to restart,
and check whether the problem is solved.
Inspection/ Solution
Check video source to make sure the volume is turned up
and the audio content is not mute.
Slide the jog lever to ← or → to check the volume level of
the projector.
Unplug and plug again the cable from the device to restart,
and check the problem is solved.
Inspection/ Solution
Hold down the jog lever for 3 seconds to enter the OSD mode.
Select [AUDIO SOURCE SETTING/ LINE OUT] to force
the audio to output from the connected speakers.
Inspection/ Solution