Anywire ASLINKAMP LA-A1AW Product Manual

Browse online or download pdf Product Manual for Touch terminals Anywire ASLINKAMP LA-A1AW. Anywire ASLINKAMP LA-A1AW 12 pages. Anywireaslink system, analog input unit ch insulated type with 7-segment

Print Page

AnyWireASLINK System Products Guide

ASLINKAMP

[Analog Input Unit (CH insulated type with 7-segment)]

L□-A1AW

[Notes on Safety]

Precautions that must be observed in order to use this system safely are

indicated as shown below. You must observe these precautions.

A WARNING indicates a potentially hazardous situation which, if not

WARNING

！

handled correctly, could result in death or serious injury.

A CAUTION indicates a potentially hazardous situation which, if not

CAUTION

！

handled correctly, may result in personal injury or property damage.

○ System Safety

！

WARNING

This system is intended for general industrial applications. It does not

have functions for supporting applications requiring higher levels of safety

such as safety-related devices or accident prevention systems.

○ Always turn off the system power before attempting to mount or replace.

○ Prolonged continuous ow of a rated load current or higher or a transit

current due to load short-circuit or similar problem, in the hybrid unit

including the output unit and the output circuit may result in smoke

generation or re. An external safety device such as a fuse must be

installed.

○ System power supply

！

CAUTION

Use a stabilized 24V DC power supply. Use of a non-stabilized power

supply may cause problems with the system.

○ Separately route high-voltage and power cables

Although the AnyWireASLINK has a high noise margin, lay the

transmission lines and I/O cables so as to keep them away from

high-voltage and power cables.

○ Connectors and terminals

・ Pay careful attention to the length and installation of cable wiring to

e n s u r e t h a t c o n n e c t o r s a n d c a b l e s a r e n e i t h e r s t r e s s e d n o r

disconnected even if they are stressed.

・ Make sure to prevent any metal objects from getting inside the

connectors or the terminal blocks.

・ Short-circuits caused by metal objects or mis-wiring are likely to

damage the device.

○ Do not impose any external loads on the units.

Doing so may cause a failure.

○ Do not disconnect or reconnect between the transmission line and slave

units when a transmission line is operating.

A malfunction may occur.

○ Use the AnyWireASLINK within the range of the speci cations and

conditions shown below.

[Warranty]

■ Warranty period

The warranty on the delivered Product shall continue to be effective for one (1)

year after the delivery thereof to a location as designated by the original owner.

■ Scope of warranty

Should a defect occur in any part of the Product during the foregoing warranty

period when it is used normally in accordance with the speci cations described

in this User's Manual, the Company shall replace or repair the defect free of

charge, except when it arises as a result of:

[1] Misuse or abuse of the Product by the owner;

[2] Fault caused by cause other than the delivered Product;

[3] Unauthorized modi cation or repair of the Product by any party other than

the Company;

[4] Any unusual force of nature, disaster, or other cause beyond the Company's

control.

The term "warranty," as used herein, refers to the warranty applicable to the

delivered product alone. The Company shall not be liable for any damages

consequential or incidental to a malfunction of the delivered product.

■ Repair at cost

After the expiration of the warranty period, any troubleshooting or repairs shall

be done at the expense of the owner.

Even during the warranty term, any repairs and troubleshooting for defects

arising from causes outside the scope of the warranty as speci ed above shall

be done at the owner's expense.

[Type]

Bit operation

Analog input unit

LA-A1AW

(CH insulated type

LB-A1AW

with 7-segment)

1CH (Base unit)

1CH (Extension unit)

-L*A1AW 1/11-

[Function]

Model

ASLINKAMP

CH insulated

Insulated

Measurement

Voltage: 0-10V, 0-5V, 1-5V

input range

Current: 4-20 mA, 0-20 mA

Resolution

1/16000

Input speci cations setting

Reference point shift mode

Functions

Average number of moving times

Address/parameter automatic setting (Base unit only)

Miniature

[Included items]

LA-A1AW (Base)

LB-A1AW (Extension)

[Name of each part]

7-segment display

Analog port

e-CON (3P)

7-segment display

Analog port

e-CON (3P)

Base unit ...1

Protective cover

Base

LED display

Transmission line

Extension

Protective cover

LED display

Expansion connector