Dymo LabelManager 100 User Manual - Page 5

Browse online or download pdf User Manual for Label Maker Dymo LabelManager 100. Dymo LabelManager 100 6 pages. Electronic labelmaker
Also for Dymo LabelManager 100: Instructions For Use Manual (18 pages)

Print Page

Note: A row of vertical dots will print between each label

as a cutting guide.

INCREMENTAL NUMBERING

Labels can be printed in increments of 1-99 automatically.

• Key in your starting number as the right most digit on

the label. Press

automatically move up a digit to the next number.

Press

then

• It is also possible to include automatic incremental

numbering when printing multiple copies.

• Key in your starting number, eg. LABEL 1 .

• Next press

then

desired number of copies are displayed eg.10.

Now press

then

LABEL 1 to LABEL 10. At fixed length setting, the

Labelmaker will stop printing when the label exceeds

the fixed length. While using fixed length setting, the

labelmaker will stop printing when the label exceeds the

fixed length.

• It is possible to print up to 99 sequentially numbered

labels at any one time.

LAST LABEL MEMORY

• The unit will store the last label text and settings when

turned off. Upon power-up, these will be restored and

displayed. Removal of the batteries for more than a few

seconds will cause this information to be lost.

Symbols and special characters

INTERNATIONAL CHARACTERS

To add a diacritical (accent) to create an international

character, enter the character first, followed immediately

by the diacritical, e.g. press

get é.

To add a diacritical to an existing character, use

to place the cursor under the character to be

changed, then press the appropriate diacritical key.

SYMBOLS

SYMBOL

Press

to show symbols and special characters,

SYMBOL

some of which are not available direct from the keyboard.

The display will show: A–C

Each letter selects a line of symbol characters, as shown

in the table on page 2.

Press

to cancel, or press a letter key 'A' to 'C' until

DEL

you find the line of symbols required.

Use

to select a symbol. Press

symbol in the label.

PRINT CONTRAST — may be adjusted by pressing

followed by 'Y' to display the five contrast symbols

• Use

to select lighter or darker print.

• Press

to confirm the setting. The contrast level will

revert to the mid-setting when the Labelmaker is turned

off and on again.

Note: This function enables you to adjust the print

quality under extreme temperature conditions.

then

the display will

to continue the sequence.

COPIES

followed by

until the

SYMBOL

this will print ten labels -

followed by

to place the

Cleaning

• Clean the cutter blade regularly: Remove the cassette,

then insert the tip of a ball pen or pencil between L-

shaped piece D

• Press and hold down cutter lever E to expose cutter

blade D

both sides of the blade. Release cutter lever E.

• Check and clean print head face D

cotton bud and alcohol ONLY.

Troubleshooting

No display

• check machine is on

• replace discharged batteries

• check AC adaptor.

No printing or poor text

• replace discharged batteries

• check tape cassette installed correctly

• clean the print head

• replace the tape cassette.

Tape jammed

• lift out tape cassette carefully

• remove/release jammed tape

• DO NOT cut the ink ribbon – turn spool

• cut off excess label tape

• refit/replace the tape cassette.

Poor cutter performance

• clean the cutter blade regularly

No response to print key

• !!!!!!!! in the display indicates a printer jam. Press any

key to return to normal display. Open the cassette

compartment and free the jam.

•

discharged batteries. Press any key to return to normal

display. Replace the batteries.

No success?

• Call the DYMO customer service hotline telephone

number in your country – see the warranty booklet.

SYMBOL

and the guide pin – see page 2.

, then use a cotton bud and alcohol to clean

flashing in the display indicates

regularly using a

to tighten