Dymo LabelManager 100 Посібник користувача - Сторінка 5
Переглянути онлайн або завантажити pdf Посібник користувача для Виробник етикеток Dymo LabelManager 100. Dymo LabelManager 100 6 сторінок. Electronic labelmaker
Також для Dymo LabelManager 100: Інструкція з використання Посібник з використання (18 сторінок)
Друкувати сторінку
Note: A row of vertical dots will print between each label
as a cutting guide.
INCREMENTAL NUMBERING
Labels can be printed in increments of 1-99 automatically.
• Key in your starting number as the right most digit on
the label. Press
automatically move up a digit to the next number.
Press
then
PRINT
• It is also possible to include automatic incremental
numbering when printing multiple copies.
• Key in your starting number, eg. LABEL 1 .
• Next press
then
desired number of copies are displayed eg.10.
Now press
then
LABEL 1 to LABEL 10. At fixed length setting, the
Labelmaker will stop printing when the label exceeds
the fixed length. While using fixed length setting, the
labelmaker will stop printing when the label exceeds the
fixed length.
• It is possible to print up to 99 sequentially numbered
labels at any one time.
LAST LABEL MEMORY
• The unit will store the last label text and settings when
turned off. Upon power-up, these will be restored and
displayed. Removal of the batteries for more than a few
seconds will cause this information to be lost.
Symbols and special characters
INTERNATIONAL CHARACTERS
To add a diacritical (accent) to create an international
character, enter the character first, followed immediately
by the diacritical, e.g. press
get é.
To add a diacritical to an existing character, use
to place the cursor under the character to be
changed, then press the appropriate diacritical key.
SYMBOLS
SYMBOL
Press
to show symbols and special characters,
SYMBOL
some of which are not available direct from the keyboard.
The display will show: A–C
Each letter selects a line of symbol characters, as shown
in the table on page 2.
Press
to cancel, or press a letter key 'A' to 'C' until
DEL
you find the line of symbols required.
Use
or
to select a symbol. Press
symbol in the label.
PRINT CONTRAST — may be adjusted by pressing
followed by 'Y' to display the five contrast symbols
.
• Use
or
to select lighter or darker print.
• Press
to confirm the setting. The contrast level will
revert to the mid-setting when the Labelmaker is turned
off and on again.
Note: This function enables you to adjust the print
quality under extreme temperature conditions.
then
the display will
PRINT
to continue the sequence.
COPIES
followed by
until the
SYMBOL
this will print ten labels -
PRINT
followed by
to
E
/
to place the
Cleaning
• Clean the cutter blade regularly: Remove the cassette,
then insert the tip of a ball pen or pencil between L-
shaped piece D
• Press and hold down cutter lever E to expose cutter
blade D
both sides of the blade. Release cutter lever E.
• Check and clean print head face D
cotton bud and alcohol ONLY.
Troubleshooting
No display
• check machine is on
• replace discharged batteries
• check AC adaptor.
No printing or poor text
• replace discharged batteries
• check tape cassette installed correctly
• clean the print head
• replace the tape cassette.
Tape jammed
• lift out tape cassette carefully
• remove/release jammed tape
• DO NOT cut the ink ribbon – turn spool
• cut off excess label tape
• refit/replace the tape cassette.
Poor cutter performance
• clean the cutter blade regularly
No response to print key
• !!!!!!!! in the display indicates a printer jam. Press any
key to return to normal display. Open the cassette
compartment and free the jam.
•
discharged batteries. Press any key to return to normal
or
display. Replace the batteries.
No success?
• Call the DYMO customer service hotline telephone
number in your country – see the warranty booklet.
SYMBOL
5
and the guide pin – see page 2.
, then use a cotton bud and alcohol to clean
flashing in the display indicates
regularly using a
B
to tighten