Great Canadian Systems IQ 2000 P Operation Manual - Page 4

Browse online or download pdf Operation Manual for Coffee Maker Great Canadian Systems IQ 2000 P. Great Canadian Systems IQ 2000 P 12 pages. Newco iq2000p: operation manual

Print Page

Program and Service Mode Functions

Programming is done through the 4 hidden buttons located on the brewer faceplate under the display.

Prior to accessing the program or service mode you will need to attach a service template to the faceplate of the

unit in order to locate the buttons. Attach one of the self stick templates to the faceplate aligning it with the display

window edges and bottom border as shown in Fig 1 on page 2.

To enter either the Program or Service Mode:

Turn the main ON/OFF switch located on the lower left front of brewer column to the OFF position.

Depress and hold down both the Brew and Cancel Buttons located on the brewer face plate. (See Fig 1, Page 2).

Continue to hold while turning the ON/OFF switch to the ON position. The brewer display will indicate to please

wait as it initializes the program/service mode. Continue holding the brew and the cancel button until the brewer

enters the Program/Service main menu (approximately 5 seconds).

Select Mode

Program

Service

The service mode is used for initial brewer fill, to display and clear error messages, to view total brew cycles, and

to view/reset the brew cycles since service.

An explanation of the various features for both modes is outlined in the following sections. Note that if at

any point after entering this menu the brewer detects that there has been no activity on the keypad for 1 minute it

will exit to the ready/standby mode. It will then be necessary to follow steps outlined above to return to the program

or service mode. If an option or feature has been changed without pressing enter prior to this occurring the change

will be lost.

Program Options

Option

Brew Time #1

Brew #2 Enable

Brew Time #2

Buzzer Delay

Auto Arm Enable

Brew Time Remaining

Temperature Setpoint

Power Save Enable

Buzzer Type

Keypad Beep Enable

Service Cycles

Exit Pgm/Srv Mode

Brew Time #1

3:30

or "+" keys may be used to change the selected numeral up or down as required to obtain the desired brew time.

Note that when setting brew time the display changes by 1 numeral each time the button is depressed. The

minimum time which may be programmed is 10 seconds and the maximum time is 5 minutes and 20 seconds.

Depress enter to save the programmed brew time.

Brew #2 Enable

Yes

This is the Program/Service main menu. Use the Select key to choose either the

Program or Service mode. The program mode is used to set custom settings such

as brew times, buzzer type, tank temperature, enable power save or auto arm, etc.

Table 1 - Summary of Program Mode Options/Features

Program Options/Value Range

10 Sec - 5 Min, 20 Sec

Yes, No

10 Sec - 5 Min, 20 Sec

10 Sec - 2 Min

Yes, No

170 F - 212 F

Yes, No

Time is factory set at

2 hours. May not be changed.

Burst, None, Steady, Single Pulse, Double

Pulse

Yes, No

0 - 65535

Yes, No

This is the length of time which the dump valve will remain open to allow water to

flow over the coffee grounds. It is the active portion of the brew cycle. The Select

key may be used to choose a numeral in the displayed time to change and the "-"

This option allows a second brew function to be programmed thereby giving the

user multiple volume brewing capability. Brew #2 is the brew cycle which would be

Factory

Setting

3:25

Dump valve open time for brew 1.

Optional second brew setting using hidden key.

1:30

Dump valve open time for brew 2.

1:00

Drain time from basket for brews 1 and 2.

Yes

Ensures optimum brew temperature.

Yes

Display time remaining during the brew cycle.

205

Water holding temperature in tank.

Yes

Drops tank temperature to 170 F during

periods (2 hours) of non use to save energy.

Steady

Signal for the completion of the brew cycle.

Yes

Audible tone to ensure keys are fully

depressed.

500

Brew Cycles to run before displaying the Call

For Service Message for routine maintenance.

N/A

Exit from programing mode to "Ready To

Brew".

- 4 -

Description