Hidro-Water XENA 10.1 User& Installer's Manual - Page 7

Browse online or download pdf User& Installer's Manual for Water Filtration Systems Hidro-Water XENA 10.1. Hidro-Water XENA 10.1 13 pages.

Print Page

5.- OSMOSIS SYSTEM START-UP

a. Make sure that all the connections are connected properly and tightened and the XENA

10.1 system is connected to the 220 – 240V power supply.

b. Make sure that the arm on the WATER STOP Antileak

system is down as shown in the figure so that the water

can enter the system.

c. Release the ⅜" tube that is connected to the osmosis

system's first membrane housing by unscrewing the

nut and facing it towards a bucket or container.

d. Open the water supply and then the ball valve (figure 9) as

shown. Make sure there is no water leak. If there is, close

the valve and fix it.

e. Let the water run until it's clear. This way we can make

sure that there isn't any residue trapped in the membrane

that the granular carbon filter could have let off.

Close the brass ball valve at the water inlet (figure 9) and reconnect the tube to the first

membrane housing by screwing on the corresponding nut.

g. Release the ¼" tube that is connected to the osmosis

system's elbow nut on the post filter by unscrewing the nut

and facing it towards a bucket or container.

h. Once again open the water supply and then the ball

valve (figure 9). Let the water run between 6 – 10

minutes to remove a chemical product that has come

from the membrane which is used to protect them

from microbiological contamination. This product isn't

dangerous but could affect the taste.

Close the brass ball valve at the water inlet (figure 9) and reconnect the tube to the post filter

by screwing on the corresponding nut.

MA-EN-OSMOSIS XENA10.1-RO-0220-22-FLC-21-V01.0

Open position

Open the brass ball valve again (figure 9) and turn the faucet (figure 3) on. In doing so, the

system will start to produce water. If the water has a black colour don't worry, this is normal.

It's caused by the residue the carbon activated granular cartridge lets off.

k. Raise the arm of the WATER STOP Antileak system and place a piece of absorbent material

as indicated in the picture. Put away the other piece to use as a spare. Lower the arm so that

water can enter the osmosis system and continue to produce water.

Once it runs clear, turn the faucet off.

m. The system is now ready for use.

CONGRATULATIONS! YOUR SYSTEM IS ALREADY FULLY INSTALLED AND RUNNING

6.- INSTALLATION & MAINTENANCE

The installer should inform the family members of the following points of the Reverse

Osmosis System:

a. Location of the water inlet, storage tank valve, faucet, drain clamp and the plug that

connects the osmosis system to the mains supply.

b. Uses for purified water (cooking, to make coffees & teas, drinking, ice cubes, ironing,

fish tanks...)

c. Maintaining the osmosis system. The recommended maintenance of the osmosis

system is in the table below. By not following the maintenance as described in this

manual, using original cartridges and by authorized personnel that guarantees the

quality of the water produced and the correct operation of the osmosis system,

the warranty will be void.

Sediments

Carbon GAC

Cartridge type

cartridge

Stage

Reference

CA-1203-02

CA-0604-08

Appearance

Replace*

6 - 9 months

Every time you change a cartridge, the membrane or a component in contact with water or

Sanitation

if you haven't consumed water in over a month, you must sanitise the system using

the Sanitising kit (OI-0207-131). Not supplied with the system.

MA-EN-OSMOSIS XENA10.1-RO-0220-22-FLC-21-V01.0

Carbon CTO

Membrane

Postfilter

cartridge

& 5

CA-0608-03

ME-2312-02

OI-0205-18

6 - 9 months

2 – 3 years**

12 months