Autopage MA-200 Installation Instructions Manual - Page 5

Browse online or download pdf Installation Instructions Manual for Security System Autopage MA-200. Autopage MA-200 8 pages. 2-way remote control motorcycle alarm
Also for Autopage MA-200: Operation Manual (13 pages)

Print Page

This will become a 1 second pulse ground by activate

capacity of this wire is 200 mA. This output can be programmed to provide the following type of output: 1

second pulse / latched / Latched with ignition / 30 / 60 / 90 seconds timer control.

H2/7. Yellow wire – Zone 5 / To Ignition Switched +12V –

This wire is connected to a switched 12 volts source. This wire should receive "12 volts" when the ignition

key is in the "ON" and "START" position. When the ignition is turned "OFF", this wire should receive "0"

voltage.

H3. START KILL BLACK WIRES ( 2 Black and 2 Black / White )

a). Find the wire from the starter solenoid, (usually located on the starter) and going to the ignition switch.

b). When found, use voltmeter, connect one probe of the voltmeter to ground and connect the other end of

the probe to the starter wire, it should receive "12 volts" only when the ignition key in the "START"

position.

c). After locating the correct wire, cut it in half, try to start the motorcycle. The engine should not "crank

over".

d). Connect the 4 wires to the 2 sets (Black with Black and Black/White with Black/White).

e). When the extend wires are needed, they must be exactly same gauge as the cut wire. Connect the cut

wire to the one of Black wire, and connect the another cut wire to the other Black wire.

H4. RF ANTENNA - BLACK THIN WIRE

The black thin wire on control module is the receiver antenna wire. Antenna placement is very important!

Ensure that it is unwrapped and stretched out with the last 6" straight and keep it away from large metal

objects or chassis for best reception.

H5. BLUE 4-PIN CONNECTOR. –

Mount the transmitter antenna module with the tie-wraps or tape.

1. The antenna module and all of its components MUST be installed in a location where they cannot

become wet and be submerged in the water.

2. Keep it away from any heat sources or obvious leaks. Also keep the components and harnesses as far

from the exhaust as possible.

3. Mount the antenna module in a hidden but accessible location

4. Keep it away from large metal objects or chassis for best reception.

A. PROGRAMMING TRANSMITTER:

Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is

exceeded, the security system will start deleting transmitters from memory in chronological order.

1. Turn the Ignition 'switch 'OFF/ON' 3 TIMES and stay in ON position. Within 15 seconds.

2. Push the Valet switch 3 times and holding in on 3rd push until a long chirp is heard then release the

valet switch. You are now in the Transmitter programming mode.

3. Press and hold any button of the transmitter until the siren responds with a confirming chirp, indicating

the signal has been stored into memory.

4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each

transmitter.

Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will

confirm exit.

B. ALARM FEATURES PROGRAMMING:

ALARM FEATURE "

" PRORAMMING:

1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.

2. Push the Valet switch 2 times and hold in on 2

release the valet switch. You are now in the Alarm feature 'I' programming mode.

3. Press and release the transmitter button 'A' corresponding to the feature 'A' you want to change.

a. The siren chirps and LED pause will indicate previously setting.

MA200 IN REV.A

button on transmitter for two seconds, the current

TRANSMITTER ANTENNA MODULE

PROGRAMMING

push until one chirp and a long chirp is heard then

Oct/23/2006