Autopage MA-200 Installation Instructions Manual - Page 6

Browse online or download pdf Installation Instructions Manual for Security System Autopage MA-200. Autopage MA-200 8 pages. 2-way remote control motorcycle alarm
Also for Autopage MA-200: Operation Manual (13 pages)

Print Page
b. The system will advance to [2] LED flash, One chirp with a long chirp. (The factory default settings is
always [1] LED flash, [1] chirp.)
4 Depress the transmitter button 'A' again to change the feature again. Simply keep re-depressing the
transmitter button 'A' again until the module advances to your desired setting.
5. Depress the transmitter button 'B' corresponding to the feature 'B' you wants to program.
Press
One Chirp /
Transmitter
LED one pulse
Button
Factory Default
Setting
All Chirps on
1
Automatic Rearm
2
on
F
Active arming
3
F
Horn Chirp 10ms
4
+
Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
Active Arming With Passive Starter Disables: The "Ground-when-armed output will go active 60
seconds after the ignition is turned off. The LED will flash at half its normal rate when the ignition is turned
off to indicate that the system will interrupt the starter in 60 seconds.
II
ALARM FEATURE "
" PRORAMMING:
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and staying in the OFF position.
2. Push the Valet switch 4 times and hold in on the 4
release the valet switch. You are now in the Alarm feature 'II' programming mode.
3. Press and release the transmitter button 'A' corresponding to the feature 'A' you want to program.
Press
One Chirp /
T
r
LED one pulse
ransmitte
Button
Factory Default
Setting
H1/5 Brown Wire =
1
Constant Siren
output
H2/6 Gray Wire
2
Channel 3 Output =
1 second pulse
F
H2/5 Violet Wire
3
Channel 4 Output =
Momentary output
Enable the out of
4
+ F
range check
Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
Momentary output = The momentary output selection will output a negative signal from the Channel 4
output immediately when the channel 4 button is pressed and will continue until the button is release.
Latched output = The latched output selection will output a negative signal as soon as the Channel 3 (4)
button is pressed and will continue until the button is pressed again.
Latched /Reset with ignition = A latched / reset with ignition output works similar to the latched output,
but will also reset (output will stop) when the ignition is turned on then off.
MA200 IN REV.A
Two Chirps /
Three Chirps /
LED two pulses
LED three pulses
Siren Chirps on only
Horn Chirps on only
Automatic Rearm off
Passive arming
Active arming with
Passive starter
disable
Horn Chirp 16ms
Horn Chirp 20ms
th
push until two chirps and a long chirp is heard then
Two Chirps /
Three Chirps /
LED two pulses
LED three pulses
H1/5 Brown Wire =
H1/5 Brown Wire =
5-second pulse Siren
Random pulse Siren
output
output
H2/6 Gray Wire
H2/6 Gray Wire
Channel 3 Output =
Channel 3 Output =
Latch
Latch with Ignition
H2/5 Violet Wire
H2/5 Violet Wire
Channel 4 Output =
Channel 4 Output =
Latched output
Latch with Ignition
Disable the out of
range check.
6
Oct/23/2006
Four Chirps /
LED four pulses
All Chirps off
Four Chirps /
LED four pulses
4 Chirps = 30-second
5 Chirps = 60-second
6 Chirps = 90-second
4 Chirps = 30-second
5 Chirps = 60-second
6 Chirps = 90-second