CENTURION SYSTEMS G-SWITCH-22 Programming Manual - Page 7

Browse online or download pdf Programming Manual for Control Unit CENTURION SYSTEMS G-SWITCH-22. CENTURION SYSTEMS G-SWITCH-22 10 pages. 2g gsm module

Print Page
Examples
(Commands have been highlighted for clarity)
Command
p.xxxx.QP.0841
234567
AT. Airtime
This command allows an airtime voucher to be loaded,
or remaining airtime to be queried.
Description
(Airtime)
AT
Loads or queries
airtime
Examples
(Commands have been highlighted for clarity)
Command
p.xxxx.AT.L.123
4567890
p.xxxx.AT.Q
CO. Configuring the Module
This command allows the functionality of the system to be
configured. Outputs can be set up, states of Input/Outputs
checked, PINs and passwords managed, etc.
Examples
(Commands have been highlighted for clarity)
Command
p.xxxx.CO.OU1PU.
OU1PT.2000
p.xxxx.CO.OU1LA.
OU2PU.OU2PT.
1500
p.xxxx.CO.SS
p.xxxx.CO.QB
p.xxxx.CO.CL
p.xxxx.CO.DSL
p.xxxx.CO.ESL
p.xxxx.CO.STR.1.
''alarm
activated".STR.5.
"power failed"
p.xxxx.CO.STR.18.
''open gate"
p.xxxx.CO.IN1R
p.xxxx.CO.IN2B
p.xxxx.CO.IN2BT.4
p.xxxx.CO.IN1FT.2
p.xxxx.CO.IN2EC.3
p.xxxx.CO.LM
A. SIM card PIN Code Settings
Command
p.xxxx.CO.CS.
yyyy
p.xxxx.CO.EP
p.xxxx.CO.DP
Description
Queries phone number 0841234567. Phone settings
are sent via SMS to the querying device.
Parameters
Load airtime (L)
Query airtime (Q)
Sub-Parameters
Airtime voucher number
Description
Loads airtime voucher number 1234567890 onto
the SIM.
Airtime remaining on the SIM is sent via SMS to
the querying device.
Output configuration
Sets Output 1 as pulsed, and sets Output 1
pulse time to two seconds (2000 milliseconds).
Sets Output 1 as latched, sets Output 2 as
pulsed, and sets Output 2 pulse time to 1.5
seconds (1500 milliseconds).
Sends an SMS to the querying phone with a
value of 5 (strongest) to 1 (weakest) for signal
strength.
Sends an SMS to the querying phone with the
battery voltage value.
Clears all the transaction logs stored in the
system's memory.
Disables sticky latches, so that when the Module's
power is cycled, the Outputs will return to their
default state and will not assume the state they
were in prior to the power cycle.
Enables sticky latches, so that when the Module's
power is cycled, the Output relays assume the
state they were in prior to the power cycle.
Configures text string 1 as "alarm activated" and
text string 5 as "power failed". If, for instance,
these text strings are assigned to certain Inputs,
an SMS containing this text will be sent to users
upon activation of the Inputs associated with
them.
Configures text string 18 as "open gate". The text
string "open gate" (without quotation marks) can
be SMSd to the Module and used to activate an
Output.
Configures Input 1 to send an SMS if a rising
edge signal is present.
Configures Input 2 to send SMSs on both rising
and falling edge activation.
Sets Input 2 to only become active and send an
SMS once four seconds have elapsed since the
previous trigger.
Sets Input 2 to become active and send an SMS
only if the Input has been valid for two seconds.
Sets Input 1 to send an SMS only if it has been
triggered three times.
Sends an SMS to the querying phone with a list
of all the messages stored in the system.
Description
Change the SIM card PIN code. yyyy is the NEW
PIN code.
Enable checking of the SIM PIN number on
startup.
Disable checking of the SIM PIN number on startup.