Gardena S 2300 SP Operating Instructions Manual - Page 4
Browse online or download pdf Operating Instructions Manual for Lawn and Garden Equipment Gardena S 2300 SP. Gardena S 2300 SP 8 pages. Quiet power chaff cutter
Print Page
GARDENA Quiet Power Chaff Cutter S 2000 S / S 2300 SP
1. Technical Data
Length
Width
Height
Weight
Power consumption
Voltage
Frequency
Fuse
ON-time
Nominal speed of motor
Nominal speed of cutting cylinder
Branch diameter of newly cut wood
Branch diameter of dry wood
Working area related emission
1)
characteristic value L
p A
1)
Noise level L
WA
1) Measuring method according to RAL UZ 54
2. Operating Instructions Information
Please read and follow these
For safety reasons chil-
A
operating instructions carefully.
dren under the age of
Familiarise yourself with the unit's
16 or people not familiar with
features, its proper use and the
these operating instructions
safety instructions included.
must not use this Chaff Cutter.
3. Proper Use
The GARDENA chaff cutter is
It is essential to observe the
designed for cutting organic
manufacturer's operating instruc-
material e.g. plant waste, in
tions to ensure the unit's proper
domestic and hobby gardens.
functioning.
The operating instructions also
It is not designed for use in public
contain advice for service, main-
facilities, parks, sporting grounds,
tenance and repair.
on roads, in agriculture or forestry.
4. Assembly
4.1 Checking whether all
.Operating instructions
the Parts are Included
The GARDENA Chaff Cutter box
4.2 Operating Parts (Fig. A)
1
contains the following parts:
Wheels
2
.Chaff cutter
Trolley
3
Chaff Cutter
.Trolley
4
.2 wheels
Axle
5
.Plastic bag with connection
Screws (4.2 x 19 mm)
parts and fork wrench
with stops
6
(10 /13 mm)
Feeding funnel
12
S 2000 S
S 2300 SP
530 mm
530 mm
482 mm
482 mm
876 mm
876 mm
23 kg
24 kg
2000 W
2300 W
230 V
230 V
50 Hz
50 Hz
16 A
16 A
AB S6 4 / 6
AB S6 4 / 6
2790 rpm
2760 rpm
40 rpm
40 rpm
up to 40 mm
up to 45 mm
up to 30 mm
up to 30 mm
82 dB (A)
82 dB (A)
95 dB (A)
95 dB (A)
Please keep these instructions
in a safe place.
Warning ! The Chaff Cutter
A
is not suitable, for exam-
ple, for preparing soil and must
never be used to chop or cut
metal parts. Danger of injury !
7
Screws
8
Holes
9
Hexagon nuts / washers
0
Chaff Cutter socket
A
Up / down switch
B
Main switch
C
Adjusting screw
D
Counter nut
E
Cutting plate
G
F
Motor protection switch
G
Cutting cylinder
4.3 Assembling the Trolley
(Fig. B)
1
Fit the two wheels
supplied
to the trolley
2
as follows:
1
1. Push the wheel
onto the
4
axle
of the trolley.
Note : Mount the wheel
correctly according to fig. B.
2. Push the stop onto the screw
5
and insert the complete
5. Putting into Operation
5.1 Location
Stand the Chaff Cutter on an
even, sturdy and stable surface.
To prevent injuries due to
material which is thrown back
out of the Chaff Cutter, do not
stand the Chaff Cutter on peb-
bles or a cemented surface.
Do not feed any more material
to be cut into the Chaff Cutter
once the cutting tool has
stopped.
5.2 Connecting the
Chaff Cutter to the Mains
A
Important Information !
Only use permitted extension
cables. Ask your electrician.
The connection sockets for
extension cables must be made
of rubber or be encased in
rubber according to DIN VDE
0620.
Never trail the cable over or
underneath the feeding funnel.
Danger of accidents and
damage !
When laying the mains cable
make sure that it does not trail
through open doors or win-
dows. Danger of squashing
the cable.
To prevent damaging the cable,
pull the plug to remove it from
the socket. Never pull the cable.
assembly into the hole of the
1. Place the chaff cutter
axle in the trolley and screw
trolley
tight.
C and insert the two screws
3. Fit the second wheel as de-
in the holes
scribed above. The chaff cutter
Note : Ensure that the chaff
can now be mounted on the
cutter is positioned correctly
trolley.
on the trolley and is not tilted.
2. Secure both screws
4.4 Mounting the Chaff Cutter
trolley from underneath using
on the Trolley (Fig. C)
the washers and hexagon
3
Mount the chaff cutter
on the
nuts provided
2
trolley
as follows:
A
To connect the Chaff Cutter to
; otherwise the cutting cylin-
the mains, plug the coupling of
der might not change direction.
the extension cable into the sock-
3. Now feed the material to be
0
et
of the Chaff Cutter and the
cut into the feeding funnel
plug into the mains socket.
(max. strength – see "Technical
Data").
5.3 Commissioning the
Note : After the cutting tool has
Chaff Cutter (Fig. D / E)
taken hold of the material to
be chopped, it is automatically
Important ! Pay attention to the
pulled in (Fig. E).
information regarding proper
Always wear gloves
use and the notes on safety
A
and protective goggles
before you start using the Chaff
when working with the Chaff
Cutter.
Cutter.
The Chaff Cutter must be as-
sembled correctly before the
5.4 The cylinder is blocked ...
motor is turned on. The feeding
if foreign bodies, too much ma-
funnel must not contain mate-
terial to be cut or branches which
rial to be cut.
are too thick are caught in the
cylinder.
Keep your face and body away
from the feeding funnel.
Proceed as follows:
1. Set the up / down switch
Keep your hands, feet and
to the
other parts of your body as well
(Fig. D 2). The Chaff Cutter
as clothes away from the feed-
stops.
ing area and ejection shaft.
2. Press the green button on
To begin using the Chaff Cutter:
the main switch
A
1. Set the up / down switch
of
on the machine again. The cut-
the cylinder to the
position
ting cylinder turn in
(Fig. D 1) (normal working
and the material to be cut is
position of the cutting cylinder).
now released upwards.
2. Press the green button on the
main switch
B
to switch on the
5.5 If the material to be cut
Chaff Cutter. The cutting cylin-
is not released despite back-
der starts.
wards position (completely
Important ! Always wait until
blocked), then the internal cutting
the cutting cylinder has
E
plate
stopped when changing direc-
the cutting cylinder as described
tions with the up / down switch
below:
G
3
on the
2
as shown in diagram
7
8
.
7
to the
9
.
6
A
position (backwards)
B
to switch
position
is to be removed from
13