Gardena S 2300 SP Operating Instructions Manual - Page 6
Browse online or download pdf Operating Instructions Manual for Lawn and Garden Equipment Gardena S 2300 SP. Gardena S 2300 SP 8 pages. Quiet power chaff cutter
Print Page
The Chaff Cutter must not be
A
tilted or tipped when in opera-
Interruptions of Work
tion.
Never leave the Chaff Cutter
Do not put stones, soil, glass,
unattended at the working area.
textiles, plastics or metal parts
If you interrupt your work
into the Chaff Cutter. These
store the unit in a safe place.
materials will seriously damage
Disconnect the mains plug!
the cutting tool. There is also
If you wish to move the Chaff
the danger of being hit by ma-
Cutter to another place, switch
terial thrown back out of the
off the motor, remove the plug
Chaff Cutter.
and wait until the cylinder
When the chaff cutter is
stops moving before moving
plugged in, never reach into
the Chaff Cutter.
the ejection shaft / feeding
funnel. Danger of injury!
A
Check the Environment
If foreign bodies fall into the
cylinder or if unusual sounds
Never use the unit when it is
or vibrations occur, switch off
raining or in damp or wet areas.
the Chaff Cutter immediately
Do not operate your Chaff
and wait until the cylinder has
Cutter near swimming pools
stopped moving. Remove the
or garden ponds.
obstacle. Check the Chaff
Cutter for any damage / loose
Please observe the prescribed
parts and if necessary have
local quiet times.
your chaff cutter repaired.
9. Faults
Problem
Possible cause
Motor will not start.
Up / down switch set to
position 0.
Motor switches off.
Blockage protection activated
due to constant overload or
blockage at the cylinder.
Chaff Cutter not accepting
Aerator direction of rotation
material to be cut.
is set incorrectly.
Collection container is over-full
(cylinder blocked).
Turning direction has automati-
cally changed due to blockage.
Cutting cylinder got stuck due
to too wet cutting material.
16
G
A
Electric Safety
The Chaff Cutter must only be
operated with undamaged elec-
tric cable. If the electric cable
or the extension cable is dam-
aged disconnect the mains
plug immediately.
Check the power cable re-
gularly for damage and signs
of wear and tear.
The socket of an extension
cable should be water-proof
or the connection sockets
for extension cables must be
made of rubber or be encased
in rubber according to DIN
VDE 0620.
Only use permitted extension
cables. Ask your electrician.
For portable units, which are
used outdoors, we recommend
to use a residual-current de-
vice having a residual-current
rating ≤ ≤ 30 mA.
In Switzerland use of a
residual-current device is
obligatory.
Remedy
Set the direction of rotation
switch to the desired position:
Material being cut is moved
upwards, e.g. if blocked
Chaff Cutter setting
The motor can be switched on
again after 5 minutes.
Move the direction of rotation
A
switch
to the correct position.
Empty the collection container.
See chapter 5.6.
Use branches to eliminate
blockage. See chapter 6.2.
Problem
Possible cause
Material to be chopped
Cutting plate
is not severed sufficiently.
at the cylinder.
Abnormal sounds,
Check whether the screws
Chaff Cutter rattling.
are loose.
If you have any problem with
GARDENA service centres listed
your Chaff Cutter, please contact
on the rear page.
our Service, or return the defec-
tive unit together with a short
We expressly point out that,
description of the problem and,
according to the product lia-
in case of guarantee,
with a copy
bility law, we are not liable for
of the receipt to one of the
any damage caused by our
units if, in case of repair or
EU Certificate of Conformity
The undersigned
GARDENA Kress + Kastner GmbH · Hans-Lorenser-Str. 40 · D - 89079 Ulm
hereby certifies that, when leaving our factory, the units indicated below are in accordance with the
harmonised EU guidelines, EU standards of safety and product specific standards.
This certificate becomes void if the units are modified without our approval.
Description of the units:
Harmonised European
Quiet Power Chaff Cutter
standards:
EN 292 -1
Types :
EN 292 - 2
S 2000 S / S 2300 SP
EN 60335 -1
Art. No.:
Noise level :
3980 / 3982
EU directives:
S 2000 S
Machinery Directive 98 / 37/ EC
S 2300 SP
Electromagnetic Compatibility
Year of CE marking:
89 / 336 / EC
1998
Low Voltage Directive 73 / 23 / EC
Directive 93 / 68 / EC
Directive 2000 / 14 / EC
Remedy
E
not set correctly
Re-adjust the cutting plate
as described in "Maintaining
the Cutting Cylinder".
Tighten the screws. Check the
the device by GARDENA Service.
exchange, other than original
GARDENA parts are used and
repair is not carried out by a
GARDENA service centre or
an authorised specialist.
The same also applies to spare
parts and accessories.
Ulm, 09.11.2001
Thomas Heinl
Technical Dept. Manager
measured / guaranteed
95 / 96 dB (A)
95 / 97 dB (A)
G
E
17