Garmin GPSMAP 5208 - Marine GPS Receiver Installation Instructions Manual - Page 7

Browse online or download pdf Installation Instructions Manual for Marine GPS System Garmin GPSMAP 5208 - Marine GPS Receiver. Garmin GPSMAP 5208 - Marine GPS Receiver 19 pages. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Also for Garmin GPSMAP 5208 - Marine GPS Receiver: Important Safety Information (4 pages), Quick Reference Manual (2 pages), Owner's Manual (2 pages), Owner's Manual (2 pages), Technical Reference (30 pages), Installation Instructions Manual (25 pages), Quick Reference Manual (2 pages), Installation Instructions Manual (25 pages), Declaration Of Conformity (1 pages), Printing Manual (2 pages), Supplement Manual (24 pages), User Manual (6 pages)

Garmin GPSMAP 5208 - Marine GPS Receiver Installation Instructions Manual
Wiring the GPS 17 Antenna
The GPS 17 antenna must be wired to the included 19-pin NMEA 0183 cable as well as to the boat's power supply. Refer to the diagram below
when wiring the GPS 17 to the 19-pin NMEA 0183 cable. Use 22 AWG shielded wiring for extended runs of wire to the NMEA 0183 cable or
GPS 17 cable. Solder all connections and seal them with heat shrink tubing.
NoTE: If you are using more than one Garmin chartplotter over a Garmin Marine Network, only wire one chartplotter to a GPS 17. The GPS
signal is shared between multiple chartplotters connected to a Garmin Marine Network.
Garmin
GPSMAP 4000/5000
Series Unit

Wiring a Garmin Marine Network

The optional Garmin Marine Network is a plug-and-play system that allows for high-speed data transfer between multiple Garmin chartplotters
and other network compatible Garmin devices such as a Garmin sonar unit (GSD 22), a Garmin radar (GMR 18 or GMR 404/406), or an XM
Weather receiver (GDL30/30A). The GPSMAP 4000/5000 units have three network ports that can be used to connect other Garmin network
compatible chartplotters and devices. If the network requires more ports, use a Garmin Marine Network port extender (GMS 10), or another
GPSMAP 4000/5000. Data from each connected component is shared by all the connected Garmin chartplotters.
Notes:
• The GPS 17 antenna and standard NMEA devices must all be wired to one chartplotter on the network. The data is then shared over the
network to other connected chartplotters.
• Connect network components, such as a Garmin GMR radar, GSD sounder, or GDL XM Weather receiver to any chartplotter on the
network or to an optional GMS 10 Network Port Expander. Data is shared between all chartplotters on the network.
• BlueChart
g2 Vision cartography data is shared between any connected GPSMAP 4000/5000 series chartplotter.
®
• Video input(s) from the Marine Video cable is only viewable on the chartplotter to which it is connected.
• You can connect a GPSMAP 4000/5000 chartplotter to a Marine Network with a GPSMAP 3000 series chartplotter:
They will share GPS 17 GPS position information as well as information to and from standard NMEA 0183 devices.
They will share information from connected network compatible Garmin devices such as a sonar unit (GSD 22), a radar (GMR 18 or
GMR 404/406), or an XM Weather receiver (GDL30/30A).
Garmin GPSMAP 3000 series units CANNOT share cartography data with the GPSMAP 4000/5000 units.
• All network components must be connected to the boat's power source according to their installation instructions. The following diagrams
show only the network connections, not power connections.
• Currently, XM Weather and audio service is only available in North America. Because of this, a connected XM Weather receiver (GDL30/
30A) will only function in North America.
GPSMAP 4000/5000 Series Installation Instructions
FUSE
7.5A - 42V
RED (POWER)
POWER
BLACK (GND)
CABLE
ORANGE (ACC. ON)
NMEA 0183
GREEN (DATA OUT)
>
CABLE
GREEN/WHITE (DATA IN)
>
Wiring the GPSMAP 4000/5000 Unit and the GPS 17
-
+
BATTERy
WIRE
10-35 VDC
COLOR
RED (POWER)
BLACK (GND)
yELLOW (ON)
BLUE (DATA IN)
WHITE (DATA OUT)
WIRE
COLOR
FUSE
1 A
GPS 17
GPS/WAAS
>
Sensor
>
7