Miller 028042103 Owner's Manual - Page 7
Browse online or download pdf Owner's Manual for Welding System Miller 028042103. Miller 028042103 20 pages.
Also for Miller 028042103: Owner's Manual (20 pages), Owner's Manual (20 pages), Owner's Manual (20 pages)
Print Page
1-1. Additional Safety Symbols And Definitions
Some symbols are found only on CE products.
2-1.
Additional Safety Symbol Definitions
Do not weld on drums or any closed containers.
�
Some symbols are found only on CE products.
?
Do not weld on drums or any closed containers.
?
Read Owner's Manual and inside labels for connection points and procedures.
= < 60
Read Owner's Manual and inside labels for connection points and procedures.
Wear dry insulating gloves. Do not wear wet or damaged gloves.
Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves.
SECTION 2 – DEFINITIONS
Do not weld on drums or any closed containers.
Falling unit can cause injury and damage. Do not move unit where two wheels are at a different height and unit
could tip
avoid tipping. Be careful when moving unit over uneven surfaces.
Protect yourself from electric shock by insulating yourself from work and ground.
Warning! Watch Out! There are possible hazards as shown by the symbols.
Do not cut on drums or any closed containers.
Do not stack racks. Lift only with proper equipment and correct procedures.
Do not discard product (where applicable) with general waste.
Reuse or recycle Waste Electrical and Electronic Equipment (WEEE) by disposing at a designated collection
Protect yourself from electric shock by insulating yourself from work and ground.
facility.
Moving parts can injure.
Do not grip material near cutting path.
Contact your local recycling office or your local distributor for further information.
Disconnect input plug or power before working on machine.
Always connect green, Or green with yellow stripe, wire to supply grounding terminal.
Turn off power before disassembling torch.
Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves.
Connect black, white, and red wires (L1, L2, L3) to line terminals.
Keep your head out of the fumes.
Pinch points can injure.
Compressed air hazard. If ANY air is injected into the skin or body seek medical help immediately.
Do not remove or paint over (cover) the label.
Protect yourself from electric shock by insulating yourself from work and ground.
Recycle.
Flying objects can injure. Wear eye protection.
Keep your head out of the fumes
3
Protect yourself from electric shock by insulating yourself from work and ground.
Use coolant suggested by the manufacturer.
Keep away from pinch points.
Become trained and read the instructions before working on machine.
Use forced ventilation or local exhaust to remove the fumes.
Disconnect input plug or power before working on machine.
Falling unit can cause injury. Do not move or operate unit where it could tip.
Please drain fluid according to instructions.
Connect green or green/yellow grounding conductor to ground terminal.
Use forced ventilation or local exhaust to remove the fumes.
3
Keep your head out of the fumes.
Hot oil and compressed air can injure or kill.
Keep your head out of the fumes
Do not move or operate unit where it could tip.
Use forced ventilation or local exhaust to remove the fumes.
GND/PE, Ground/Protective Earth
Use forced ventilation or local exhaust to remove the fumes.
Engine fuel plus flames or sparks can cause fire.
Remove unit from shipping crate. Remove Owner's Manual from un
Follow instructions to install muffler.
Warning! Watch Out! There are possible hazards as shown by the
symbols.
Become trained and read the instructions before working on the
machine or welding.
Do not discard product (where applicable) with general waste.
Read Owner's Manual. Read labels on unit.
Reuse or recycle Waste Electrical and Electronic Equipment (WEEE)
by disposing at a designated collection facility.
Contact your local recycling office or your local distributor for further
information.
Wear hat and safety glasses. Use ear protection and button shirt
Move jumper links as shown on inside label to match input voltage
Hazardous voltage remains on input capacitors after power is turned
collar. Use welding helmet with correct shade of filter. Wear complete
job site. Include extra length in grounding conductor and connect
off. Do not touch fully charged capacitors. Always wait
body protection.
grounding conductor first. Connect line input conductors as shown
after power is turned off before working on unit, AND check input ca-
inside label. Double-check all connections, jumper link positions, an
pacitor voltage, and be sure it is near 0 before touching any parts.
Disconnect input plug or power before working on machine.
Turn power off before connecting to 115 volt receptacle.
input voltage before applying power.
Become trained and read the instructions before working on the
machine or welding.
Hazardous voltage remains on input capacitors after power is turned
Plugged filter or hoses can cause overheating to the power source
off. Do not touch fully charged capacitors. Always wait
and torch.
power is turned off before working on unit, AND check input capacitor
Do not remove or paint over (cover) the label.
voltage, and be sure it is near 0 before touching any parts.
Wear hat and safety glasses. Use ear protection and button shirt
collar. Use welding helmet with correct shade of filter. Wear complete
Move jumper links as shown on inside label to match input voltage at
Always lift and support unit using both handles. Keep angle of lifting
body protection.
job site. Include extra length in grounding conductor and connect
device less than 60 degrees.
Every 100 hours, check and clean filter and check condition of hos
grounding conductor first. Connect line input conductors as shown on
inside label. Double-check all connections, jumper link positions, and
Use a proper cart to move unit.
Recycle.
input voltage before applying power.
Engine fuel plus flames or sparks can cause fire.
Close door before turning on unit.
Use coolant suggested by the manufacturer.
Move jumper links as shown on inside label to match input voltage at
job site. Include extra length in grounding conductor and connect
grounding conductor first. Connect line input conductors as shown on
Remove unit from shipping crate. Remove Owner's Manual from unit.
Read the Owner's Manual before working on this machine.
inside label. Double-check all connections, jumper link positions, and
Follow instructions to install muffler.
Please drain fluid according to instructions.
input voltage before applying power.
Read the labels on the welding power source, wire feeder, or other
Read Owner's Manual. Read labels on unit.
Close door before turning on unit.
Read the labels on the welding power source, wire feeder, or other
major equipment for welding safety information.
Connect input conductors (L1, L2 And L3) to line terminals.
major equipment for welding safety information.
Move jumper links as shown on inside label to match input voltage at
Welding current creates an electric and magnetic field (EMF)
job site. Include extra length in grounding conductor and connect
around the welding circuit and welding equipment.
Read the Owner's Manual before working on this machine.
grounding conductor first. Connect line input conductors as shown on
Read Owner's Manual before working on this machine.
inside label. Double-check all connections, jumper link positions, and
input voltage before applying power.
Read the labels on the welding power source, wire feeder, or other
Plugged filter or hoses can cause overheating to the power source
Plugged filter or hoses can cause overheating to the power source
major equipment for welding safety information.
and torch.
and torch.
Always connect green wire to supply grounding terminal, never to a
Welding current creates an electric and magnetic field (EMF)
line terminal.
around the welding circuit and welding equipment.
Connect black, white, and red wires (L1, L2, L3) to line terminals.
Every 100 hours, check and clean filter and check condition of hoses.
Read manual.
Safe15 2012
Safe97 201
Safe2 201
Safe45 201
Safe16 201
Safe98 201
Safe64 2017 04
Safe46 201
Safe3 201
Safe1 2012
Safe17 201
Safe99 201
Safe65 2012 06
Safe47 201
Safe37 2017
Safe4 201
Safe18 201
Safe100 201
60 seconds
Safe64 2017 04
Safe66 2012 06
Safe49 201
Safe42 2017 04
Safe5 201
Safe2 2017
Safe19 201
Safe101 201
Safe 107 2012
5 minutes
after
Safe65 2012 06
Safe67 2012 06
Safe43 2017 04
Safe50 201
Safe6 201
Safe102 201
Safe20 201
Safe108 201
Safe3 2017
Safe66 2012 06
Safe44 2012 05
Safe51 201
Safe68 2012 06
Safe7 201
Safe103 201
Safe109 201
Safe4 2017
Safe67 2012 06
Safe45 2012 05
Safe52 201
Safe110 201
Safe8 201
Safe69 2012 06
Safe104 201
Safe5 2017
Safe46 2012 05
Safe68 2012 06
Safe53 201
Safe 111 201
Safe9 201
Safe70 2012 06
Safe105 201
Safe6 2017
Safe47 2012 05
Safe 112 201
Safe69 2012 06
Safe71 2012 06
Safe 106 201
Safe7 2017
Safe 113 201
Safe72 2012 06
Safe49 2012 05
Safe70 2012 06
Safe8 2012
Safe 114 201
Safe71 2012 06
Safe73 2017 04
Safe50 2012 05
Safe9 2012
OM-254203 Page 3
Safe72 2012 06
Safe115 2013
OM-
Safe51 2012 05
O