FIBARO FGMS-001 Operating Manual - Page 9

Browse online or download pdf Operating Manual for Security Sensors FIBARO FGMS-001. FIBARO FGMS-001 11 pages. Motion sensor
Also for FIBARO FGMS-001: Operating Manual (20 pages), Operating Manual (2 pages)

Print Page

This parameter provides backward compatibility with controllers not

supporting Z-Wave+.

Available settings: 0 - backward compatible tamper alarm sent to

Default setting:

40. Illuminance report - threshold

This parameter determines the change in light intensity level result-

ing in illuminance report being sent to the main controller.

Available settings: 0 - reports are not sent

Default setting:

42. Illuminance report - interval

NOTE

Time interval between consecutive illuminance reports. The reports

Frequent illuminance

are sent even if there is no change in the light intensity.

reports will shorten

the battery life. Pa-

Available settings: 0 - periodical reports are not sent

rameter value under

5 may result in block-

ing the temperature

Default setting:

reports.

60. Temperature report - threshold

This parameter determines the change in measured temperature that

will result in new temperature report being sent to the main controller.

Available settings: 0 - reports are not sent

Default setting:

62. Temperature measuring - interval

NOTE

Time interval between consecutive temperature measurements. The

Temperature

meas-

shorter the time, the more frequently the temperature will be meas-

urements

are

still

ured, but the battery life will shorten.

performed during the

wake up, even if the

Available settings: 0 - temperature is not measured

periodic measuring is

disabled

(parameter

62 set to 0).

Default setting:

NOTE

64. Temperature report - interval

Frequent temperature

Time interval between consecutive temperature reports. The reports

reports will shorten

are sent even if there is no change in the temperature.

the battery life. Pa-

Available settings: 0 - periodical reports are not sent

rameter value under

5 may result in block-

ing the illuminance

Default setting:

reports.

ADvAnCED PARAMETERS

5th association group

1 - backward compatible tamper alarm sent in

broadcast mode

Parameter size:

1 [byte]

1-32767 (illuminance in lux)

200 (200 lux) Parameter size:

2 [bytes]

1-32767 (in seconds)

3600 (1h)

Parameter size:

2 [bytes]

1-255 (0.1-25.5°C, 0.1°C step)

20 (1°C)

Parameter size:

2 [bytes]

1-32767 (in seconds)

900 (900s)

Parameter size:

2 [bytes]

1-32767 (in seconds)

Parameter size:

2 [bytes]

66. Temperature offset

The value to be added to the actual temperature, measured by the

sensor (temperature compensation).

Available settings: -1000-1000 (-1000-1000°C, 1°C step)

0 (0°C)

Default setting:

Parameter size:

80. Visual LED indicator - signalling mode

This parameter determines the way in which visual indicator behaves

after motion has been detected.

Available settings: 0 - LED inactive,

values from 1 to 9 - single long blink at the mo-

ment of reporting motion. no other motion will

be indicated until alarm is cancelled.

colour

temperature

2 - Flashlight Mode, 3 - white, 4 - red, 5 - green,

6 - blue, 7 - yellow, 8 - cyan, 9 - magenta

values from 10 to 18 - single long blink at the

moment of reporting motion and one short

blink each time the motion is detected again.

10 - colour is temperature dependent,

11 - Flashlight Mode, 12 - white, 13 - red,

14 - green, 15 - blue, 16 - yellow, 17 - cyan,

18 - magenta

values from 19 to 26 - single long blink at the

moment of reporting motion and two short

blinks each time the motion is detected again.

19 - colour is temperature dependent,

20 - white, 21 - red, 22 - green, 23 - blue,

24 - yellow, 25 - cyan, 26 - magenta

Default setting:

Parameter size:

81. Visual LED indicator - brightness

This parameter determines the brightness of the visual LED indicator

when indicating motion.

Available settings: 0 - brightness determined by the illuminance

(parameters 82 and 83)

1-100 (1-100%)

50 (50%)

Default setting:

Parameter size:

82. Visual LED indicator - illuminance for low indicator brightness

Light intensity level below which brightness of visual indicator is set

to 1%.

Available settings: 0 to value of parameter 83 (in lux)

Default setting:

100

Parameter size:

2 [bytes]

NOTE

Flashlight

Mode

visual indicator glows

in white for 10 sec-

onds. If value of pa-

rameter 80 is set to 11,

each detected motion

extends the glowing

by next 10 seconds.

dependent,

1 [byte]

CAUTION

The value of parame-

ter 83 must be higher

than the value of pa-

rameter 82.

2 [bytes]

ADvAnCED PARAMETERS