Sharp FO-IS115N Quick Setup Manual - Page 2

Browse online or download pdf Quick Setup Manual for All in One Printer Sharp FO-IS115N. Sharp FO-IS115N 6 pages. Workgroup document communication system
Also for Sharp FO-IS115N: Specifications (2 pages)

Print Page

Load paper.

1. Fan the paper, and then

tap the edges against a

flat surface to even the

stack.

3. Push the paper plate

back down.

Check the machine's IP address and the

connection.

The machine requires an IP address to

communicate.

If your network is set up to automatically assign IP

addresses (DHCP enabled), the machine will

automatically receive an IP address when it is

connected.

If your network requires that a static IP address be

assigned to the machine, see Network Settings on

page 45 of the online guide to set the IP address.

Follow these steps to check the machine's IP

address and the connection:

1. Press

, then

INFO

INFORMATION] appears.

2. Press

Configure e-mail settings for Scan to E-mail in the machine's Web page.

The machine's Web page can be accessed from any computer connected to the same

network as the machine. Type in the machine's host name (or IP address) in the address bar

of your computer's Web browser. (See "9" above to check the machine's host name.) When

the Web page opens, click E-mail Setup in the menu frame.

1. Type in the host name of the

machine in your browser's

address bar.

2. Click

E-mail

Setup to

open the

e-mail

settings.

6. When finished, click Submit to save your settings.

2. Pull the paper plate forward

➊

. Squeeze the paper guide

and adjust it to the width of

➋

the paper

. Insert the stack

of paper into the tray, print

➌

side up

•

If the display shows [IP ADDRESS/DHCP: ON],

the machine received an IP address automatically

and is able to communicate. The IP address

appears on the second line. To show the machine's

host name, press

•

If the display shows [IP ADDRESS/DHCP: OFF] a

static IP address has been set and the machine is

able to communicate. The IP address appears on

the second line. To show the machine's host name,

press

•

If [NOW CONNECTING / CHECK LATER]

until [NETWORK

appears, press

repeat the procedure again.

3. Enter the host name or

IP address of your SMTP

Server.

Connect the machine to your network.

The machine is connected using an Ethernet cable (not included).

Please purchase a 10Base-T/100Base-TX straight-through

(regular) cable.

Connect one end of the cable to the LAN port on the machine.

Connect the other end to a LAN port on your switch or hub. A

typical setup is shown below.

STOP

to exit, wait briefly, and then

4. If your SMTP server

requires SMTP

Authentication, select

this checkbox and

enter your User Name

and Password.

if your service requires

POP before SMTP,

select this checkbox and

enter the information

that follows.

5. Enter a Sender Name

and an E-mail Address.

(An address of an

existing account can be

used; responses to e-

mail sent from the

machine will be sent to

this address.)

English

Router

LAN cable

LAN ports

LAN cable

Switch/Hub

If a message appears indicating that the

machine is unable to communicate...

•

Check the Ethernet cable. Are the connections

secure? Are you using straight-through (not

crossover) cable for 10Base-T/100Base-TX?

•

Try removing and then restoring the power to

the router or other device to which the machine

is connected.

•

If the display shows [IP ADDRESS/DHCP:

FAIL], the machine was unable to obtain an IP

address automatically. Remove and then

reinsert the Ethernet cable. Restart the device

that acts as your DHCP server.

For more information, see pages 29 and 30 of the

online guide.

Install the printer driver.

Install the printer driver on each

computer that will use the machine as a

printer.

•

To use the machine as a printer, it

must be connected to your network

and have an IP address as explained

in "9" above.

1. Insert the CD-ROM that

accompanied the machine into your

computer's CD-ROM drive.

2. In the initial screen that appears, click

"Install Printer Driver".

•

If the initial screen does not

automatically appear, run

"Launch.exe" on the CD-ROM. (Open

"My Computer", double-click your

CD-ROM drive, and double-click

"Launch.exe".)

•

To select the language, click the

"Language Options" button.

3. Follow the on-screen instructions to

install the printer driver.

Internet

LAN cable