Sony BluetoothH MEX-BT5100 Operating Instructions Manual - Page 31

Browse online or download pdf Operating Instructions Manual for Stereo System Sony BluetoothH MEX-BT5100. Sony BluetoothH MEX-BT5100 45 pages. Bluetooth audio system
Also for Sony BluetoothH MEX-BT5100: Installation/Connections (2 pages), Installation/Connections (2 pages), Quick Manual (2 pages), Specifications (2 pages), Quick Manual (2 pages), Quick Manual (2 pages)

Print Page

Sony BluetoothH MEX-BT5100 Operating Instructions Manual

Instalaci6n/Conexiones

Installation/Connections

Installation/Connexions

Bluetooth™

Audio System

- -

3-276-519-21 (1)

SONY;

MEX-BT5100

2007 Sony Corporation

Printed in Thailand

not supplied

non tourni

no suministrado

Connection diagram []]

To a metal surface of the car

First connect the black ground lead, then connect the

orange/white striped, yellow, and red power input leads.

To the power antenna control lead or power

supply lead of antenna booster amplifier

Noles

It is not necessary to connect this lead if there is no power

antenna or antenna booster,

with a manually-operated

telescopic antenna.

When your car has

built-in FMIAM antenna in the rearl

side glass. see "Notes on the control and power supply

leads."

To AMP REMOTE IN of an optional power

amplifier

This connection

only for amplifiers. Connecting any other

system may damage the unit.

To the interface cable of a car telephone

To a car's illumination signal

Be sure to connect the black ground lead to

metal surface

the car first.

To the +12 V power terminal which is

energized in the accessory position of the

ignition key switch

Notes

• If there is no accessory position, connect to the

12 V

power (battery) terminal which

energized at all times.

Be sure to connect the black ground lead to

metal

surface of the car first.

• When your car has

built-in FMIAM antenna in the rearl

side glass, see "Notes on the control and power supply

leads."

To the +12 V power terminal which is

energized at all times

Be sure to connect the black ground lead to

metal surface

the car first.

Noles on Ihe control and power supply leads

The power antenna control lead (blue) supplies

+ 12

V DC

when you turn on the tuner.

• When your car has built-in FMIAM antenna in the rearlside

glass, connect the power antenna control lead (blue) or the

accessory power input lead (red) to the power terminal

the

existing antenna booster. For details, consult your dealer.

A power antenna without a relay box cannot be used with this

unit.

Memory hold connection

When the yellow power input lead

connected. power will

always be supplied to the memory circuit even when the ignition

switch

turned off.

Notes on speaker connection

Before connecting the speakers, turn the unit off.

Use speakers with an impedance

4 to 8 ohms, and with

adequate power handling capacities to avoid its damage.

• Do not connect the speaker terminals to the car chassis, or

connect the terminals 01 the right speakers with those 01 the

left speaker.

Do not connect the ground lead

this unit to the negative (-)

terminal 01 the speaker.

Do not attempt to connect the speakers in parallel.

Connect only passive speakers. Connecting active speakers

(With built-in amplifiers) to the speaker terminals may damage

the unit.

To avoid

malfunction, do not use the built-in speaker leads

installed in your car if the unit shares

common negative (-)

lead lor the right and left speakers.

Do not connect the unit's speaker leads to each other.

Note on connection

If speaker and amplifier are not connected correctly, "Failure"

appears in the display. In this case, make sure the speaker and

amplifier are connected correctly.

Connection example

[gJ

Parts list

• This unit is designed for negative ground 12 V DC

operation only.

• Do not get the leads under a screw, or caught in moving

parts (e.g. seat railing).

• Before making connections, turn the car ignition off to

avoid short circuits.

• Connect the yellow and red power input leads only

after all other leads have been connected.

• Run all ground leads to a common ground

point.

• Be sure to insulate any loose unconnected leads with

electrical tape for safety.

• Do not cover the ventilation slots or heat sinks of the

unit.

• The use of optical instruments with this product will

increase eye hazard.

Notes on the power supply lead (yellow)

• When connecting this unit in combination with other

stereo components, the connected car circuit's rating

must be higher than the sum of each component's fuse.

• When no car circuits are rated high enough, connect

the unit directly to the battery.

Note

Before installing, make sure that the catches on both sides

the bracket

are bent inwards 2 mm (3/32 in).

the catches are

straight or bent outwards, the unit will not be installed securely

and may spring oul.

Catch

Be sure to install this unit in the dashboard of the car

as the rear side of the unit becomes hot during use.

Cautions

• The numbers in the list are keyed to those in the

instructions.

• The bracket

and the protection collar

are

attached to the unit before shipping. Before mounting

the unit, use the release keys

to remove the bracket

and the protection collar

from the unit. For

details, see "Removing the protection collar and the

bracket

<EI)"

on the reverse side of the sheet.

• Keep the release keys

for future use as they

are also necessary if you remove the unit from

your car.

Caution

Handle the bracket

carefully to avoid injuring your

fingers.

Rotary commander RM-X4S

Satellite de commande RM-X4S

Mando rotatorio RM-X4S

CDIMD changer

Changeur de CD/MD

Cambiador de CD/MD

Power amplifier

Amplificateur de puissance

Amplificador de potencia

I I

Active subwoofer

Caisson de graves actif

Altavoz potenciador de

graves activo

Rear speaker

Haut-parleur arriare

Altavoz posterior

Front speaker

Haut-parleur avant

Altavoz frontal

Equipment used in illustrations (not supplied)

Appareils utilises dans les illustrations (non fournis)

Equipo utilizado en las i1ustraciones (no suministrado)

Notes

<III-A)

• Be sure to connect the ground lead before connecting the

amplifier.

• The alarm will only sound il the built-in amplifier

used.

Tip

<III-BoO)

For connecting two or more CD/MD changers. the source

selector XA-C40 (not supplied)

necessary.