Epson PowerLite 1825 User Manual - Page 4

Browse online or download pdf User Manual for Software Epson PowerLite 1825. Epson PowerLite 1825 14 pages. Release of check tool for network projectors v1.00 for windows
Also for Epson PowerLite 1825: User Manual (42 pages), Operation Manual (36 pages), Quick Setup (2 pages), Operation Manual (47 pages), Declaration Of Conformity (4 pages), Product Specification (2 pages), Parts List (1 pages), Product Support Bulletin (25 pages), Product Support Bulletin (38 pages), Product Support Bulletin (12 pages), Product Support Bulletin (42 pages), Product Support Bulletin (22 pages), Product Support Bulletin (28 pages), Product Support Bulletin (41 pages), Product Support Bulletin (34 pages), Product Support Bulletin (38 pages), Product Support Bulletin (28 pages), Product Support Bulletin (15 pages), Product Support Bulletin (22 pages)

Epson PowerLite 1825 User Manual
PowerLite 1825
3. Press the P
button on the remote control or on top
Power
of the projector.
The projector beeps once and the
as the projector warms up, then an image begins to appear.
When the
light stops flashing and remains green, the
Power
projector is ready for use.
4. If you are prompted to enter a password, see page 9.
Warning: Never look into the lens when the lamp is on. This can
damage your eyes and is especially dangerous for children.

Using the Direct Power On Function

The Direct Power On function enables faster setup. The
projector starts up automatically when you plug it in or turn it
on with a wall switch. You don't have to press the P
button.
Follow these steps to enable Direct Power On:
1. Press the
button on the remote control or projector
Menu
and select the
Extended
2. Choose
and press
Operation
3. Choose
Direct Power On
4. Highlight
and press
On
5. Press
to exit. The setting will take effect the next
Menu
time you plug in the projector.
Note: If a power outage occurs when Direct Power On is enabled
and the projector is plugged in, the projector will restart when the
power is restored.
4
light flashes green
Power
Power
menu.
.
Enter
and press
.
Enter
.
Enter

Shutting Down the Projector

This projector incorporates Instant Off technology. To turn it
off, you can press the P
power switch that supplies power to the projector. You don't
have to wait for the projector to cool off first.
1. To turn off the projector, press the P
remote control or projector. You see a confirmation
message. (If you don't want to turn it off, press any other
button.)
2. Press the P
Power
turns off and you can unplug the power cord.
If you want to turn the projector on again, make sure the
orange
light is not flashing, then press the P
Power
button.
Note: Turn off this product when not in use to prolong the life of the
projector. Lamp life results vary depending on the mode selected,
environmental conditions, and usage.

Sleep Mode

You can set the projector to automatically turn off the lamp and
enter "sleep mode" when it has not received any signals for up
to 30 minutes. This conserves electricity, cools the projector,
and extends the life of the lamp. You can enable sleep mode in
the Extended menu under
projector, unplug the power cord. If you want to start
projecting again, press the P

Troubleshooting Display Problems

You Can't Project an Image
If you don't see the image you are trying to project, try the
following:
❏ Make sure the cables are connected correctly.
❏ Make sure the
Power
A/V mute slide (lens cover) is open.
❏ If you've connected more than one computer and/or video
source, you may need to press the
on the projector's control panel or the
the remote control to select the correct source. (Allow a few
seconds for the projector to sync up after pressing the
button.)
❏ If you're using a PC notebook, see the next section.
2/08
button, unplug it, or turn off a
Power
button on the
Power
button again. The projection lamp
. If you are done using the
Operation
button.
Power
light is green and not flashing and the
Source Search
button on
Search
Power
button