Epson PowerLite 1825 Kullanıcı Kılavuzu - Sayfa 4

Yazılım Epson PowerLite 1825 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Epson PowerLite 1825 14 sayfaları. Release of check tool for network projectors v1.00 for windows
Ayrıca Epson PowerLite 1825 için: Kullanıcı Kılavuzu (42 sayfalar), Kullanım Kılavuzu (36 sayfalar), Hızlı Kurulum (2 sayfalar), Kullanım Kılavuzu (47 sayfalar), Uygunluk Beyanı (4 sayfalar), Ürün Özellikleri (2 sayfalar), Parça Listesi (1 sayfalar), Ürün Destek Bülteni (25 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (12 sayfalar), Ürün Destek Bülteni (42 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (41 sayfalar), Ürün Destek Bülteni (34 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (15 sayfalar), Ürün Destek Bülteni (22 sayfalar)

Sayfayı Yazdır

PowerLite 1825

3. Press the P

button on the remote control or on top

Power

of the projector.

The projector beeps once and the

as the projector warms up, then an image begins to appear.

When the

light stops flashing and remains green, the

Power

projector is ready for use.

4. If you are prompted to enter a password, see page 9.

Warning: Never look into the lens when the lamp is on. This can

damage your eyes and is especially dangerous for children.

Using the Direct Power On Function

The Direct Power On function enables faster setup. The

projector starts up automatically when you plug it in or turn it

on with a wall switch. You don't have to press the P

button.

Follow these steps to enable Direct Power On:

1. Press the

button on the remote control or projector

and select the

Extended

2. Choose

and press

Operation

3. Choose

Direct Power On

4. Highlight

and press

5. Press

to exit. The setting will take effect the next

time you plug in the projector.

Note: If a power outage occurs when Direct Power On is enabled

and the projector is plugged in, the projector will restart when the

power is restored.

light flashes green

Power

menu.

Enter

and press

Enter

Shutting Down the Projector

This projector incorporates Instant Off technology. To turn it

off, you can press the P

power switch that supplies power to the projector. You don't

have to wait for the projector to cool off first.

1. To turn off the projector, press the P

remote control or projector. You see a confirmation

message. (If you don't want to turn it off, press any other

button.)

2. Press the P

Power

turns off and you can unplug the power cord.

If you want to turn the projector on again, make sure the

orange

light is not flashing, then press the P

Power

button.

Note: Turn off this product when not in use to prolong the life of the

projector. Lamp life results vary depending on the mode selected,

environmental conditions, and usage.

Sleep Mode

You can set the projector to automatically turn off the lamp and

enter "sleep mode" when it has not received any signals for up

to 30 minutes. This conserves electricity, cools the projector,

and extends the life of the lamp. You can enable sleep mode in

the Extended menu under

projector, unplug the power cord. If you want to start

projecting again, press the P

Troubleshooting Display Problems

You Can't Project an Image

If you don't see the image you are trying to project, try the

following:

❏ Make sure the cables are connected correctly.

❏ Make sure the

Power

A/V mute slide (lens cover) is open.

❏ If you've connected more than one computer and/or video

source, you may need to press the

on the projector's control panel or the

the remote control to select the correct source. (Allow a few

seconds for the projector to sync up after pressing the

button.)

❏ If you're using a PC notebook, see the next section.

2/08

button, unplug it, or turn off a

Power

button on the

Power

button again. The projection lamp

. If you are done using the

Operation

button.

Power

light is green and not flashing and the

Source Search

button on

Power

button