Pioneer Super Tuner IIID DVH-P5000MP Installation Manual - Page 4

Browse online or download pdf Installation Manual for Car Receiver Pioneer Super Tuner IIID DVH-P5000MP. Pioneer Super Tuner IIID DVH-P5000MP 8 pages. 2004 mobile entertainment systems
Also for Pioneer Super Tuner IIID DVH-P5000MP: Owner's Manual (34 pages), User Manual (24 pages), Operation Manual (4 pages)

Print Page

Installation

• If installation angle exceeds 30° from horizon-

Notes

tal, the unit might not give its optimum perfor-

• Before finally installing the unit, connect the

mance. (

)

Fig. 7

wiring temporarily, making sure it is all con-

nected up properly, and the unit and the sys-

tem work properly.

• Use only the parts included with the unit to

ensure proper installation. The use of unautho-

rized parts can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifica-

tions of the vehicle.

• Install the unit where it does not get in the

• The cords must not cover up the area shown in

driver's way and cannot injure the passenger if

the figure below. This is necessary to allow the

there is a sudden stop, like an emergency stop.

amplifires to radiate freely. (

Fig. 8

• The semiconductor laser will be damaged if it

overheats, so don't install the unit anywhere

hot — for instance, near a heater outlet.

Do not close this area.

DIN front/rear-mount

This unit can be properly installed either from "Front" (conventional DIN Front-mount) or "Rear" (DIN

Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to

the following illustrated installation methods.

Installation

DIN front-mount

Installation with the rubber bush (Fig .9)

Holder

After inserting the holder into the dash-board, then

select the appropriate tabs according to the thick-

Dashboard

ness of the dash-board material and bend them.

(Install as firmly as possible using the top and

182

bottom tabs. To secure, bend the tabs 90 degrees.)

Fig. 7

Rubber bush

Screw

)

Removing the unit (Fig. 10) (Fig. 11)

Frame

Fig. 8

Insert the supplied extraction

keys into the unit, as shown in

the figure, until they click into

place. Keeping the keys pressed

against the sides of the unit,

pull the unit out.

Installation

DIN rear-mount

Installation using the screw holes on the side of the unit (Fig. 12) (Fig. 13)

(Fig. 14)

1 Remove the frame. (Fig.12)

Frame

Fig. 9

2 Fastening the unit to the factory radio mounting bracket. (Fig. 13) (Fig. 14)

Insert the release pin into the hole

in the bottom of the frame and

pull out to remove the frame.

(When reattaching the frame,

point the side with a groove down-

wards and attach it.)

Fig. 10

Factory radio mounting bracket

Fig. 11

Installation

Fixing the front panel

If you do not operate the Detaching and Replacing the Front Panel Function, use the supplied fixing

screws and holder to fix the front panel to this unit.

1. Attach the holders to both sides of the front panel. (Fig. 15)

Insert the release pin into the

2 Replace the front panel to the unit. (Fig. 16)

hole in the bottom of the

frame and pull out to remove

the frame. (When reattaching

the frame, point the side with

a groove downwards and

attach it.)

Fig. 12

Select a position where the screw holes of the

bracket and the screw holes of the head unit

3. Flip the holders into upright positions. (Fig. 17)

become aligned (are fitted), and tighten the

screws at 2 places on each side. Use either

truss screws (5 × 8 mm) or flush surface

screws (5 × 9 mm), depending on the shape of

the screw holes in the bracket.

Fig. 13

Screw

4 Fix the front panel to the unit using fixing screws. (Fig. 18)

Dashboard or Console

Fig. 14

Holder

Fig. 15

Fig. 16

Fig. 17

Fixing screw

Fig. 18