Pioneer Super Tuner IIID DVH-P5000MP Руководство по установке - Страница 4
Просмотреть онлайн или скачать pdf Руководство по установке для Автомобильный приемник Pioneer Super Tuner IIID DVH-P5000MP. Pioneer Super Tuner IIID DVH-P5000MP 8 страниц. 2004 mobile entertainment systems
Также для Pioneer Super Tuner IIID DVH-P5000MP: Руководство пользователя (34 страниц), Руководство пользователя (24 страниц), Руководство по эксплуатации (4 страниц)
Печатать страницу
Installation
• If installation angle exceeds 30° from horizon-
Notes
tal, the unit might not give its optimum perfor-
• Before finally installing the unit, connect the
mance. (
)
Fig. 7
wiring temporarily, making sure it is all con-
nected up properly, and the unit and the sys-
tem work properly.
• Use only the parts included with the unit to
ensure proper installation. The use of unautho-
rized parts can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifica-
tions of the vehicle.
• Install the unit where it does not get in the
• The cords must not cover up the area shown in
driver's way and cannot injure the passenger if
the figure below. This is necessary to allow the
there is a sudden stop, like an emergency stop.
amplifires to radiate freely. (
Fig. 8
• The semiconductor laser will be damaged if it
overheats, so don't install the unit anywhere
hot — for instance, near a heater outlet.
Do not close this area.
DIN front/rear-mount
This unit can be properly installed either from "Front" (conventional DIN Front-mount) or "Rear" (DIN
Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to
the following illustrated installation methods.
Installation
DIN front-mount
Installation with the rubber bush (Fig .9)
Holder
After inserting the holder into the dash-board, then
select the appropriate tabs according to the thick-
Dashboard
ness of the dash-board material and bend them.
(Install as firmly as possible using the top and
182
bottom tabs. To secure, bend the tabs 90 degrees.)
Fig. 7
53
Rubber bush
Screw
)
Removing the unit (Fig. 10) (Fig. 11)
Frame
Fig. 8
Insert the supplied extraction
keys into the unit, as shown in
the figure, until they click into
place. Keeping the keys pressed
against the sides of the unit,
pull the unit out.
Installation
DIN rear-mount
Installation using the screw holes on the side of the unit (Fig. 12) (Fig. 13)
(Fig. 14)
1 Remove the frame. (Fig.12)
Frame
Fig. 9
2 Fastening the unit to the factory radio mounting bracket. (Fig. 13) (Fig. 14)
Insert the release pin into the hole
in the bottom of the frame and
pull out to remove the frame.
(When reattaching the frame,
point the side with a groove down-
wards and attach it.)
Fig. 10
Factory radio mounting bracket
Fig. 11
Installation
Fixing the front panel
If you do not operate the Detaching and Replacing the Front Panel Function, use the supplied fixing
screws and holder to fix the front panel to this unit.
1. Attach the holders to both sides of the front panel. (Fig. 15)
Insert the release pin into the
2 Replace the front panel to the unit. (Fig. 16)
hole in the bottom of the
frame and pull out to remove
the frame. (When reattaching
the frame, point the side with
a groove downwards and
attach it.)
Fig. 12
Select a position where the screw holes of the
bracket and the screw holes of the head unit
3. Flip the holders into upright positions. (Fig. 17)
become aligned (are fitted), and tighten the
screws at 2 places on each side. Use either
truss screws (5 × 8 mm) or flush surface
screws (5 × 9 mm), depending on the shape of
the screw holes in the bracket.
Fig. 13
Screw
4 Fix the front panel to the unit using fixing screws. (Fig. 18)
Dashboard or Console
Fig. 14
Holder
Fig. 15
Fig. 16
Fig. 17
Fixing screw
Fig. 18