Pioneer X-HX33 Operating Instruction - Page 22

Browse online or download pdf Operating Instruction for Receiver Pioneer X-HX33. Pioneer X-HX33 36 pages. Cd/receiver system

Print Page

Listening to the Radio

Auto station search

The auto station search function automatically

searches for radio stations that have good

reception.

Press and hold the + or – button.

Release the button once the frequency shown

in the display panel starts changing. The auto

search function will automatically stop at the

next station that has good reception.

Notes concerning auto station search

• The auto search function may not operate correctly

from 90 MHz to 108 MHz in the FM band, due to

interference from TV signals. In such cases, use the

manual station selection method.

• When TV reception shares some bandwidth with FM

reception,it may interfere with the FM signals.

Tuning interval

The two factory settings for the AM tuning

interval are 10 kHz per step (in U.S. and Cana-

dian models) and 9 kHz per step (in Taiwanese

and European models).

The two factory settings for the FM tuning

interval are 100 kHz per step (in U.S. and

Canadian models) and 50 kHz per step (in

Taiwanese and European models).

When using the CD/Receiver System in a region

that has a different AM/FM frequency band

allocation, perform the following operation to

change the AM/FM tuning interval from 10 kHz/

100 kHz per step to 9 kHz/50 kHz per step (or

vice-versa).

While tuned to an AM or FM station, press and

hold the STOP button first, then press and hold

the MODE button. Keep all two buttons

pressed for at least three seconds.

The AM/FM tuning range is switched as shown

in Table below.

Model

Default settings

Taiwanese

AM: 531 to 1,602

and

kHz in 9-kHz

European

step

models

FM: 87.50 to 108.00

MHz in 50-kHz

step

U.S. and

AM: 530 to 1,700

Canadian

kHz in 10-kHz

models

step

FM: 88.0 to 108.0

MHz in 100-kHz

step

Switched to

AMW: 530 to 1,600

kHz in 10-kHz

step

FMW: 88.0 to 108.0

MHz in

100-kHz

AMW: 531 to 1,602

kHz in 9-kHz

step

FMW: 87.50 to

108.00 MHz

in 50-kHz step

Presetting radio stations

Preset your favorite radio stations in the CD/

receiver's memory. Up to 12 FM and 12 AM

stations can be stored in memory.

Tune the radio to the station to be

preset.

Press and hold the ENTER button for at

least three seconds.

Make sure "PGM" appears in the display

panel, which indicates that the radio station

you were tuned to at Step 1 has been stored

in memory.

Memory registration number of radio

station

To preset another station

When you press and hold the ENTER button to preset a

radio station, the tuner is set to preset station select

mode (see the next page). To preset another radio

station, perform the following steps.

Press and hold the + or – button to select a station

using the auto station search function.

Press and hold the ENTER button for at least three

seconds.

To cancel Preset Station Select mode, press the MODE

button repeatedly until "PGM" no longer appears in the

display panel.

If 12 stations have already been preset

If "FULL" appears in the display panel when you try to

preset another radio station, it means there is no more

room in memory for additional preset stations. You must

clear at least one of the previously preset radio stations

before any additional stations can be preset.

See the next page for instructions on clearing preset

radio stations.

Radio stations must be preset again in the

following situations:

• If the power plug is disconnected from the wall

socket

• If a power outage occurs

PGM