esera automation 11336 User Manual - Page 2
Browse online or download pdf User Manual for Gateway esera automation 11336. esera automation 11336 9 pages. W/auto-e-connect
Print Page
The Auto-E-Connect functionality will be available from mid-2020 via 1-Wire Controllers, 1-Wire Gateways and
1-Wire ECO from ESERA available.
Further information on ESERA Auto-E-Connect can be found on the ESERA website, ESERA Config-Tool 3, or in
the download area for this article in the ESERA Webshop.
4
Product features
Standalone controller
The 1-Wire Gateway 11 Modbus is designed to control 1-Wire Networks. You no longer have to worry about
1-Wire commands or algorithms to analyze sensor data. 1-Wire Gateway 11 Modbus scans 1-Wire Networks
by itself in order to identify new sensors or actuator devices. All data found were automatically provided in a
ready to use Modbus protocol format.
Formatted Data Output
1-Wire Gateway 11 Modbus provides plausibility checked sensor and actuator data in a ready to use format. E.g.
temperature sensor provides values in Celsius degrees with 2 decimal places. You only need to divide this
number by 100. Within the 1-Wire Gateway a product specific transformation table is available for most of our
selling 1-Wire sensor and actuator products.
Designed for all 1-Wire Networks
The 1-Wire interface of the 1-Wire Gateway 11 Modbus is specially designed to securely support all sizes of
1-Wire networks. 1-Wire sensor devices can be operated in parasitic or normal mode at the same time.
The latest available most powerful 1-Wire interface for a maximum level of data security has been used. This
includes complex network structures as well.
1-Wire Gateway 11 Modbus configuration
Free configuration software (Config-Tool 3) is provided. When using Config-Tool 3, the latest documentation
is available at any time hence it automatically updates via internet. This software is available for
our webpage. Communication to Modbus TCP is parallel with no switching.
System time / real time clock
No real time clock available in your system? No problem at all. 1-Wire Gateway 11 Modbus is providing time and
date as real time clock including an integrated backup battery. Data plausibility check is possible at any time.
Power supply
Input voltage for 1-Wire Gateway 11 Modbus is 9 – 30 VDC. Therefore it can be used for 12 V as well as 24
VDC (industrial applications). Appropriate hat-rail mounted power supplies or power plugs can be found in
our webshop.
Operation
"How-To"-Videos for setup and operation can be found on our website
How to – Support videos).
Basics and tips for 1-Wire network systems can be found in our webshop
grundlagen/) or in our e-book which is also available in our webshop
support/dokumentation/352/grundlagen-1-wire-bus-ebook?number=11901).
5
Technical data
Data Interface:
Ethernet Interface:
Firmware Update:
Power supply:
Power consumption:
1-Wire interface:
Protective circuits:
Connection:
Output voltage:
Isolation:
All rights reserved. Reproduction as well as electronic duplication of this user guide, complete or in part, requires the written consent of
ESERA GmbH. Errors and technical modification subject to change. ESERA GmbH, ESERA-Automation 2020
www.esera.de
Modbus TCP and ESERA ASCII text protocol
TCP/IP or UDP
- 10/100 MBit Ethernet Interface (RJ45)
- Auto Negotiation (Full-duplex and Half-duplex)
- Auto MDI/MDIX
- Support for DHCP and fix IP-address
via ESERA Config-Tool 3
9 – 30 VDC
maximum 500 mA
1-Wire bus (5 V, GND and data)
ESD protection and polarity protection
Screw terminals (up to 2,5 qmm wire cross section)
5 V (+/- 10 %), maximum 200 mA, overload-proof and short-circuit-proof
Galvanic separation among data and 1-Wire interface
11336 V2.0 R1.0 Manual
(Service and Support –
www.esera.de
(https://www.esera.de/1-wire-
(https://www.esera.de/service-
download
on
Page 2 of 9