ASI 0362 Installation Instructions - Page 2

Browse online or download pdf Installation Instructions for Dispenser ASI 0362. ASI 0362 2 pages.

Print Page

7. OPERATION INSTRUCTIONS

A. Service Instructions

1.Open housing with included security key previously retained.

2.Open cover on battery compartment, remove battery box and unplug cable;

install four (4) new Alkaline Type AA 1.5V batteries with correct polarity

(note the +/- indication, fig. 7) to obtain 6.0V DC ± 10% at the plug.

3.Reinstall battery box (note plug polarity tab) and close compartment cover.

4.Obtain a disposable soap cartridge (800ml) or remove, clean out and refill

(fig. 8) the included reusable soap reservoir with the correct viscosity liquid

soap (ensure that soap container cover is closed and air vent hole is open

and nozzle is not clogged and that soap container is clean (no spill-over)

and not leaking) and install either in the dispenser. Make sure the nozzle

flange is below the housing cradle rib to stretch the valve tube.

5.Make sure to latch the cradle gate.

6.Observe that the LED is lit blue and then flashes three (3) times indicating proper

operation "stand-by" condition and battery charge level (push up the cover safety interlock

switch (blue stem) on bottom to click and hold it).

7.Close the housing cover and lock it with the included security key previously retained.

8.Trigger the sensor with hands or a towel to check proper soap dispensing cycle (fig. 9).

VENT HOLE

TAB

fig. 7

Type AA 1.5V x 4

fig. 8

B. User's Instructions

1.Place hand below the dispenser spout within the sensing range. The dispenser will

automatically release the preset amount of liquid soap from the nozzle spout.

2.Obtain additional soap by withdrawing hand and then again placing hand below the

dispenser spout within the sensing range.

8. SENSING RANGE

Sensing is automatically controlled to set the appropriate distance for the triggering zone.

This is based upon mounting height above the counter or floor and the ambient and reflected

lighting conditions. There are no user adjustable controls for this feature.

It is important to observe the guidelines in Section 4 (on reverse side of these instructions) and

install unit above the minimum distance noted for each type of field condition.

If lighting conditions change during the life of the installation the unit will automatically readjust

itself to accommodate the new environment with no intervention by owner.

Countertop reflective quality changes constitute a new environment condition and may require

dispenser relocation to just above the appropriate minimum height as noted in Section 4 (on

reverse side of these instructions).

6. INSTALLATION STEPS CHECK

1.Check to ensure that dispenser is firmly attached to mounting surface.

2.Check to ensure that correct viscosity soap is filled into reservoir.

3.Check to ensure that soap container cover is closed and air vent hole is not blocked.

4.Check to ensure that soap container is clean (no spill-over) and not leaking.

5.Check to ensure that cradle gate is latched on valve tube (lift, push and press down to engage pins to latch or

unlatch in reverse operation).

6.Check to ensure that four (4) new Alkaline Type AA batteries are installed with correct polarity (note the +/- indication,

fig. 7, and below, typical).

7.Check to ensure that the battery box plug is properly engaged with the cable and the compartment door is closed.

8.Check to ensure that the LED is lit blue and then flashes three (3) times by pushing up the cover safety

interlock switch (blue stem) on bottom to click and hold it.

9.Check to ensure that the housing is properly locked and the security key is retained.

10.Check to ensure that the plastic nozzle cap was removed.

9.IMPORTANT NOTICE

1. Ensure no bright source is aimed or reflected at the

sensor from below.

2. Use fresh new liquid soap only and clean the soap

container properly before each re-fill. Deposits of old

soap will lead to malfunction and jamming.

3. Do not dilute liquid soap unless concentrate and do not

use soap containing abrasive. Observe indicated

viscosity factor of liquid soap.

fig. 9

4. Do not immerse the soap dispenser in water or clean it

RIB

under running water. This will lead to short circuit.

5. Should the dispenser be out of order and batteries have

been replaced, do not attempt any repair work. Call your

dealer for professional assistance.

11.TROUBLESHOOTING

Problem Symptom

No soap dispensed on hands

Battery LED indicator no flash

Low volume soap dispensed

Soap leaks at bottom of housing

AA (1.5V)

Caution : Batteries installed with incorrect polarity may cause malfunction.

10. BATTERY LOW INDICATION

With housing cover open and soap reservoir removed

(see Service Instructions) perform the following

diagnostic test:

1.Press and push up the cover safety interlock switch

(blue stem) on bottom to click and hold it.

2.Observe that the LED

three (3) times indicating proper operation "stand-by"

condition and battery charge level.

3.If LED continue

positive to replace the batteries.

Solution Diagnostic

Check soap qualities, properties and level in reservoir

Check sensor cover for dirt obscuring the lens

Check battery charge level

Check spout nozzle, cap air hole and valve tube for clogs

Check for reflected sensor signals jamming detector

Replace batteries

Remove soap container and wash out spout nozzle, cap air hole

and valve tube and replace with fresh new soap

Check if cradle gate is not properly latched

Check if valve tube is loose in cradle or cross-threaded

Check if valve tube cross-threaded onto bottom of reservoir or

reservoir is damaged/punctured

Check disposable soap cartridge for defects and/or replace

is lit blue and then flashes

s to flash blue the indication i