Ekinex EK-SN2-TP Gebruiksaanwijzing - Pagina 4

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Ekinex EK-SN2-TP. Ekinex EK-SN2-TP 7 pagina's. Knx standard wall presence detector with movement function

Pagina afdrukken
Limitazione of the detection area
The detection area can be limited, in order to avoid
unwanted activations, by means of the supplied optical
shielding filters. The shield consists of three layers, each
divided into four units, capable of masking an angle of
approx. 50 ° each.
When mounting the device at a height of 1.2 m - 1.5 m,
the detection range is:
• Layer A: masks the area with a circle from about 0m
to 9m.
• Layer B: masks the area with a circle from about 0m
to 3m.
• Layer C: masks the area with a circle from about 0m
to 1m.
Cut the screen for the lens provided, to remove the sec-
tors related to the desired detection area.
a b c d
200
O
200
O
Layer A eliminated Layer B eliminated
200
O
98 7
3
1
0 3
1
8 7
9
98 7
98 7
3
1
0 3
1
8 7
9
98 7
3
98 7
7
98 7
3
1
0 3
1
8
9
a
d
a
d
a
d
a
b
c
d
a b
c
d
a b
c
d
Apply the screen by inserting the edge between the lens
and the external ring, in the central and lateral grooves.
A
B
C
200
200
O
O
200
200
O
O
Layer C eliminated
200
200
O
O
3
1
0 3
1
8 7
9
98 7
3
1
0 3
1
1
0 3
1
8 7
9
98 7
3
1
0 3
1
7
98 7
3
1
0 3
1
8
9
3
1
0 3
1
Detection pattern
Unit: meter
200
O
200
O
A
A
200
O
B
A
B
C
B
C
C
98 7
3
1
0
1
3
7
98 7
3
1 1
0
3
7
98 7
3
1 1
0
3
7
A
200
O
Detection pattern
Unit: meter
A
200
O
A
200
O
98 7
3
1
0
1
3
8 7
98 7
7
3
1
0
1
3
98 7
3
1
0
1
3
7
9 8
To remove the screen, press slightly with a screwdriver in
the central groove and remove it carefully.
Connection of the KNX bus line
The connection of the KNX bus line is made with the ter-
minal block included in delivery and inserted into the slot
of the housing.
Bus
KNX
The connection procedure is as follows:
• strip the KNX bus cables with the appropriate tool (not
included in the supply), exposing about 5-6 mm);
• finish the end with the clamp
8 7
9
8 7
9
• connect the device to the bus cable terminated by the
7
8
9
standard terminal block on the back of the device.
At this point it is recommended to carry out the commis-
sioning of the device (see "Commissioning"), or at least
the download of the physical address, using the program-
ming button placed close to the bus connector.
8
9
9 8
9 8
9
Please check the user manual for further details on instal-
lation and commissioning.
9 8
!
4
Warning! In order to supply the KNX bus lines use
only KNX bus power supplies (e.g. ekinex EK-AB1-
TP, EK-AG1-TP or EK-AM1-TP). The use of other
power supplies can compromise the communica-
tion and damage the devices connected to the bus.