Electrolux # Servicehandleiding - Pagina 41

Blader online of download pdf Servicehandleiding voor {categorie_naam} Electrolux #. Electrolux # 49 pagina's. Over the range microwave oven
Ook voor Electrolux #: Handleiding voor installatie-instructies (8 pagina's), Gebruiks- en onderhoudshandleiding (20 pagina's), Gebruiks- en onderhoudshandleiding (36 pagina's), Gebruiks- en onderhoudshandleiding (24 pagina's), Gebruiks- en onderhoudshandleiding (38 pagina's), Receptenboek (17 pagina's), Instructieboekje (12 pagina's), Gebruiks- en onderhoudshandleiding (20 pagina's), Instructieboek (16 pagina's), Instructieboek (12 pagina's), Insrtuctiehandleiding (16 pagina's), Gebruikershandleiding (11 pagina's), Gebruiks- en onderhoudshandleiding (26 pagina's), Gebruiks- en onderhoudshandleiding (38 pagina's), Gebruikershandleiding (9 pagina's), Gebruiks- en onderhoudshandleiding (16 pagina's), Gebruiks- en onderhoudshandleiding (16 pagina's), Handleiding voor installatie-instructies (21 pagina's), Gebruikershandleiding (16 pagina's), Gebruiks- en onderhoudshandleiding (16 pagina's)

Pagina afdrukken
Electrolux # Servicehandleiding
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Note: The door on a microwave oven is designed to
act as an electronic seal preventing the leakage
of microwave energy from oven cavity during
cook cycle. This function does not require that
door be air-tight, moisture (condensation)-tight
or light-tight. Therefore, occasional appearance
of moisture, light or sensing of gentle warm air
movement around oven door is not abnormal
and do not of themselves indicate a leakage of
microwave energy from oven cavity.
. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure
of "Removal of Oven from Wall" and "Outer case
Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood exhaust louver from the oven cavity
by pushing the right and left tabs of the hood exhaust
louver. (Refer to the procedure of "HOOD EXHAUST
LOUVER REMOVAL".)
5. Remove door assembly, refer to "Door Replacement".
Replacement of door components are as follows:
6. Place door assembly on a soft cloth with latches facing
up.
Note:
As the engaging part of choke cover and door frame
are provided at 5 places, do not force any particular
part.
CHOKE COVER
7. Insert a putty knife (thickness of about 0.5mm) into the
gap A between the choke cover and door stopper and
between the choke cover and the door frame as shown
Figure C-3 to free engaging parts.
8. Pry the choke cover by inserting a putty knife in order
shown in Figure C-3.
9. Now choke cover is free from door panel and door
frame.
DOOR FRAME
0. Remove six (6) screws holding the door panel and the
door handle to the door frame assembly.
. Release the door frame assembly from the door panel.
NOTE: It is easier to release the engaging parts of the upper
or lower door hinge pin side at first.
2. Now, door frame assembly is free.
RE-INSTALL
Door assembly
Latch
Heads
Figure C-2. Door Replacement and adjustment

DOOR DISASSEMBLY

LATCH SPRING, LATCH HEAD AND DOOR PANEL
3. Release the latch spring from the tab of the latch head
and tab of the door frame.
4. Release the latch head from the door frame.
5. Now, the latch spring, latch head and door frame are
free.
Choke Cover
DOOR GLASS
6. Remove the glass stopper from the door frame by
releasing the tab of door frame.
7. At first, slide the door glass toward the glass stopper
side, and then slide it up. And release it from the right
and lower long tabs of the door frame.
8. Release the door glass from the upper long tab of the
door frame.
9. Release the door glass from the long tabs of the door
frame.
20. Now, the door glass is free.
4
Tab
Upper Door
Hige Pin
Upper
Oven
Hige
Lower
Oven Hige
Lower Door
Hige Pin
RE-INSTALL
A
Figure C-3. Door Disassembly
GLMV169GSB
GLMV169GBB
GLMV169GQB
PLMVZ169GCB
PLMVZ169GCC
Hood Exhaust Louver
Tab
Door Stopper
Door Stopper
Putty Knife
Door Frame